3
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of
electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not
modify the plug in any way.
Be sure the power supply you are using agrees with the nameplate marking on the heat
gun. The gun is designed to run on 120-volt, 60-cycle, alternating current (ordinary house
current). Voltage decreases greater than 10% can cause loss of power and possible
overheating.
The tool is double insulated for added safety. This means there are two separate layers
of insulation between the operator and the tool's electrical system. WARNING: Double
insulation does not take the place of normal safety precautions when operating the heat gun.
Double insulation acts as a safeguard against injury resulting from a possible electrical
insulation failure inside the tool.
Tool built with double insulation are not intended to be grounded. Because of this, the
gun's power cord is fitted with a two-pronged plug suitable for use in any conventional 120-
volt electrical outlet. Additional ground connections need not be made. WARNING: When
servicing double-insulated tools, use ONLY IDENTICAL REPLACEMENT PARTS. Replace
damaged cords.
Model no.
:
NEG-301A
Watt
:
1200W
Voltage operating
:
120 VOLTS 60Hz.
Temperatures
:
LOW 45 C ~ HIGH 500 C
Cord length
:
2 M
Weight
:
0.7 KG
Amperage
:
10 A
!
!
!
!
Inspect tool cords periodically and if damaged, have repaired by authorized service personnel.
When working on small or irregular shaped objects, secure work in a vise or clamps.
Disconnect the tool when not in use. Avoid unintentional starting. If the gun stops during
operating, disconnect from the power supply and have gun serviced by authorized service
personnel.
Stay alert! Always pay attention to the work at hand and use common sense when operating
this and all tools. Do not operate the tool when you are tired or taking medication or drugs
that may make you drowsy.
POWER INFORMATION
TECHNICAL DATA
4
Before plugging into the electrical outlet, always make certain the power switch is in the
OFF position.
When ready to begin work, set power switch to desired temperature settings. With
the heat gun, always allow a minute or so for it to reach its full operating temperature.
Always wear protective gloves and eye protection.
The heat gun is very light and easy to use. It is designed with a built-in stand so it can
be positioned in an upright (vertical) position only, on any flat, level surface. This frees
both hands to easily shape and mold PVC pipe and other materials. Remember to keep
hands away from the immediate nozzle area.
Turn on the gun and allow it reach full heating power. Hold the nozzle 3" to 4" from the
paint to be removed. After a short time, paint will soften and begin blistering. Do not overheat
paint, as this will cause burning and make the finish more difficult to remove. When stripping
paint overhead, always use eye protection.
Begin scraping the paint off, working from top to bottom. Use accessory scrapers.
Scrape with smooth, even strokes, warming the surface in front of the scraper by moving the
gun slightly from side to side. If paint is warmed properly, even thick layers can be removed
in a single pass. Paint should come off in a strip equal in width to the scraper blade.
Clean the edge of scraper often to keep it clean and sharp and to prevent paint from
building up on the blade. Scrape the paint as soon as it softens since it will quickly harden
again.
Shaped or profiled surface can be stripped with a wire brush after softening with the
hot air jet.
Cover all surfaces NOT to be heated with nonflammable material. Never concentrate
tool's heat on a window panel or other glass surface.
Never use the heat gun in combination with chemical strippers.
Use in well-ventilated areas only. Peelings and residue from lead-based paints are
poisonous.
Easy removal of paint and varnish requires some practice and the use of simple
working techniques described here. In all cases, test results on a small section of paint
before moving on to larger areas.
Note: The heat gun is designed to remove both oil and latex-based paints and
varnishes. It will not remove stains or primer coats that have impregnated the surface of
wood.
CAUTION: LEAD PAINT FUMES ARE VERY HARMFUL. ALWAYS PROVIDE
ADEQUATE VENTILATION WHILE WORKING INDOORS.
USING THE HEAT GUN
PAINT AND VARNISH REMOVAL
