for use of the
j
stim on the hand
First charge both batteries using the included charging cords. (Jstim device and heat controller)
1. Lay out all components (clockwise): Orange Conductive Glove; Grey Compression Glove; Arm Band with
ground pad; Infrared Heat Band (IHB), heat controller; Jstim Device with lead wires; conductive spray, and
compression wrap.
2. Try on the orange conductive glove for a custom stretch, then remove.
3. Spray the inside of the orange conductive glove (active) with 2-3 sprays of conductive spray and then insert
your hand back into the glove. Also spray the black patch on the arm band.
4. Pull the grey compression glove over the orange conductive glove. Insert the Infrared Heat Band in between
the conductive glove and the compression glove. Note: The emission side faces the hand.
5. The arm band is applied to the upper portion of the same arm as the glove (around the biceps area). Make it
comfortable and taught.*
6. To hook up the Jstim Electrotherapy Device, first plug the red pin connector of your lead wires into the
orange glove pigtail, and then the black pin connector into the pigtail cord that is positioned on the arm
band.** Now plug the infrared heat band into the heat controller. Turn on and adjust both devices to desired
settings (see “Device Settings” section).
for use of the
j
stim on the knee
First charge both batteries using the included charging cords. (Jstim device and heat controller)
1. Lay out all components: knee wrap; black and orange electrode pads; Infrared Heat Band (IHB), heat
controller; Jstim device and leadwires; conductive spray , and compression wrap. [Fig. A]
2. Identify the top part of the knee wrap [Fig. B]
3. Velcro your Infrared Heat Band to the knee area of the knee wrap [Fig. B]. The emission side of the
heat band faces the knee – see IhB Emission Diagram.
4. The black electrode pad Velcros to the thigh area, and the orange electrode pad Velcros to the knee
area, on top of the Infrared Heat Band.* [Fig. C]
5. Thread the lead wires through the holes in the wrap to the other side of the wrap. [Fig. D]
6. Connect the leadwire end plugs (black and red pins) into the respective pin connectors on the black and
orange electrodes (red pin into the orange pad (knee) and black pin into the black pad (thigh)).
7. Spray the electrode patches with the conductive spray (2-3 sprays is recommended).** [Fig. E]
8. Wrap on the knee wrap and velcro it closed. [Fig. F]
9. To hook up the Jstim Electrotherapy Device, plug the lead wires into the device. Connect the infrared heat
band cord to the heat controller. Turn on and adjust both devices to the desired settings (see “Device Set-
tings” section). [Fig. F]
10. The Jstim Device can be positioned to securely fit directly on the knee wrap using the compression wrap to
secure it down. Same as with the heat controller.
* If you feel that the orange electrode has slipped down during treatment, make sure to adjust until you feel it is perfect, or re-wrap
until it is. NOTE: The infrared heatband does not touch the knee.
** The optimal amount of sprays should be 2-3 sprays per garment electrode. Too many sprays can produce a stronger stimulation
than desired/recommended; which means the user will most likely have to turn down their intensity to a more comfortable level. When
using electrotherapy conductive garment material it is recommended to turn your intensity to where you can feel it, and then turn it
down to where you barely can.
*** Also, note, when lying down [or rolling around while sleeping] or setting things on your lap – pressure against your pads can adjust
your intensity up. So take this into account before sleeping with the Jstim on.
cut-away view
IHB
EMISSION DIAGRAM
IHB emission side
IHB insulation side
JStim Electrotherapy Device
Li-polymer
Rechargeable
Battery
Li-polymer
Rechargeable
Battery
LONG SIDE UP
Infrared Heat Band
may be placed on
either the palm-side
or back of the hand
IHB
EMISSION DIAGRAM
IHB emission side
IHB insulation side
*For the red and black fasteners on the lead wires: At the end of the leads supplied with your system, you will find red and black adapt-
ers. These are Cathode and Anode respectively. More sensation tends to come from the black adapter (cathode) at times.
** Make sure your black electrode in the arm band is positioned on the outside of bicep. The inside of your bicep is much more
tender, and not recommended for placement. The arm band is placed on the same arm that the Jstim hand glove is used upon.
Your system should come pre-assmbled, however for detailed setup, see below.
1. After a treatment, air dry the Jstim and/or clean as follows:
The outside of the device (ensure device is off) may be cleaned with a cloth.
Do not use liquids or chemicals for cleaning. A decontamination formula can
be used instead. Do not open the signal generator by removing the screws.
The signal generator should be turned “OFF” when not in use. Always store the
stimulator in a clean, dry area between 0° and 140°F. The Jstim wrap should
be hand washed using mild soap, and/or warm water. Air drying is then best
The conductive patches can be detached from the wrap to clean easier.
*Please note, you may notice a mild redness in the treatment areas due to the conducted
current passing through the skin, creating friction. This is normal for all types of electrother-
apy, and a hypo-allergenic aloe vera moisturizer can help relieve the redness or a cortisone
cream. If your skin appears to have an allergic reaction to any of the parts or treatments,
please discontinue use and consult your physician.
• Turn off device
• Un-Velcro the straps, remove
• Clean skin with soap and water
• Allow system to air dry
• If needed hand wash in cold water
• No bleach
