background image

17

                   

                   FCC COMPLIANCE AND ADVISORY STATEMENT 

     This device complies with Part 15 of the FCC rules. Operation is subject to the following 

two conditions: (1) 

this device may not cause harmful interference, and 

(2)

 this device 

must accept any interference received, including interference that may cause undesired 
operation. 

This equipment has been tested and found to comply with the limits for a Class B digital 
device, according to Part 15 of the FCC rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This equipment 
generates, uses and can radiate radio frequency energy and if not installed and used in 
accordance with the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. If 
this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try correct the 
interference by one or more of the following measures: 

1.  

Reorient the receiving antenna. 

2.  

Increase the separation between the equipment and receiver. 

3.  

Connect the equipment into and outlet on a circuit different from that to which the 

     receiver is connected. 

4.  

Consult the dealer or an experienced radio/TV technician for help. 

Any special accessories needed for compliance must be specified in the instruction manual. 

WARNING: 

A shielded-type power cord is required in order to meet FCC emission limits 

and also to prevent interference to the nearby radio and television reception. It is essential 
that only the supplied power cord be used. Use only shielded cables to connect I/O devices to 
this equipment. 

CAUSION: 

Any changes or modifications not expressly approved by the party responsible 

for compliance could void your authority to operate the equipment.

Summary of Contents for PT760


















Reviews: