The Packard Bell Portable Oximeter quickly and accurately measures
your oxygen (SpO2) level and pulse rate. Simply place your finger
inside the Oximeter and quickly get an accurate reading.
WARNING
Please read these instructions carefully before using this product and
keep the instructions and the oximeter in a safe place.
• For non-medical use.
• This device is only intended for sports and recreational use.
• Keep out of reach of children under 12 years.
• Please follow the general safety precautions when using on children.
• This oximeter is not waterproof. Never immerse into water or other liquids.
• If damaged, do not attempt to repair the product, instead please
contact customer support.
• Do not use the Oximeter in a magnetic resonance (MR) environment.
• Do not allow children under 12 years to take their measurements
unattended.
• Do not use abrasive cleaning agents (see Care and Cleaning).
• Do not use the oximeter outside the specified operating and storage
temperature ranges.
• Remove batteries when storing for long periods.
• Do not use the oximeter for purposes other than its original design.
• Avoid dropping the oximeter and protect it from severe impact and
shock.
BUTTONS AND DETAILS
DISPLAY DESCRIPTION
Note:
The readings might differ based on several factors such as age,
sex, location.
INSTALLING BATTERIES
1. Open the battery cover as shown.
2. Insert two new AAA alkaline batteries
(not included) following the polarity
(+/-) diagram in the compartment. Do
not mix old and new batteries, or mix
different types or brands of battery.
3. Close the battery cover.
USING THE OXIMETER
Before using the oximeter, make sure your finger and the oximeter’s finger
sensor are clean. Please see “Care and Cleaning” (Page 8)
1. Press down on the edge of the oximeter and place your index finger
into the oximeter’s finger sensor (nail side upward) as shown below.
2. Press the
POWER
button to turn the oximeter ON.
3. While the oximeter is working the numbers will fluctuate and the
oximeter will beep. Keep you finger steady and wait until the
Indicator
graph
displays a consistent pattern and the numbers stop fluctuating
as shown below.
4. Take your finger out of the oximeter. The oximeter will automatically
power off after 10 seconds of inactivity.
Note:
If the signal strength is low, switch to another finger and perform
the test again.
CHANGING THE DISPLAY ORIENTATION
You can change the display’s orientation by pressing the
POWER
button
once. Press the
POWER
button again to scroll through the four orientation
options below.
Note
: While changing the orientation of the display, if you press the
power button 4 times, it will also turn off the oximeter’s beeping sound.
To turn it back on, simply press the POWER button again 4 times.
ATTACHING THE STRAP
The strap can be attached to the oximeter by following the instructions
below:
SPECIFICATIONS
Model: PBO1
Type: Pulse Oximeter
Display: OLED
SpO2 Measuring Range: 0% - 100%
SpO2 Accuracy: ±3% in the range of 70% - 100%
Not defined < 70%
Pulse Rate Measuring Range: 25-250 bpm
Pulse Rate Accuracy: ±2 bpm
Peak wavelength: 666nm - 905nm
Automatic Shut-off: After 10 seconds of inactivity
Operation Environment: 5°C - 40°C; Humidity <80%
Storage Environment: -10°C - 50°C; Humidity <90%
Power Source: Two 1.5V AAA alkaline batteries
CARE AND CLEANING
Use a cotton swab moistened with alcohol (70% Isopropyl) to clean the
oximeter casing and rubber. Do not use abrasive cleaning agents. Never
soak the device in water or other cleaning liquids. Wait 10 minutes after
cleaning before taking a measurement.
Power button
--
---
bpm
--
PI %
PR
SpO
2
%
Designed and distributed by Southern Telecom Inc. © 2020
All Rights Reserved.
Packard Bell® is a registered trademark of PBX Holding LLC.
Images simulated and may differ from the actual product.
Made in China.
For questions or help with your product, please visit:
www.customersupport123.com
04