background image

Servicing of double-

insulated appliances

This vacuum cleaner is double insulat-
ed. In a double insulated appliance, two
systems of insulation are provided
instead of grounding.  No grounding
means is provided on a double-insulat-
ed appliance, nor should a means for
grounding be added.  Servicing a dou-
ble-insulated appliance requires
extreme care and knowledge of the sys-
tem,  and should be done only by quali-
fied service personnel.  

Replacement

parts must be identical to those parts
being replaced.  

A double-insulated

appliance is marked with the words
“DOUBLE-INSULATION” or “DOUBLE-
INSULATED”.  

The symbol      may also be marked on
the appliance.

Lubrication

The motor is equipped with bearings
that contain sufficient lubrication for the
life of the motor. The addition of lubricant
could cause damage. 

Therefore, do not

add lubricant to motor bearings.

The agitator is equipped with two ball
bearings that should be lubricated peri-
odically by a Pacific Floor Service 
Center.

Service

12

If a minor problem occurs, it usually can
be solved quite easily when the cause is
found by using the checklist below.

If you have a
problem

Possible cause             

Possible solution

• Not firmly plugged in  
• 

Plug unit in firmly

• No voltage in wall plug
• 

Check fuse or breaker      

• Blown fuse/tripped breaker
• 

Replace fuse/reset breaker

Possible cause

Possible solution

• Broken or worn belt              
• 

Replace belt

• Brush roll brushes worn
• 

Replace brush roll

• Filter bag full
• 

Change filter bag

• Incorrect carpet height setting
• 

Move nozzle control to type of    

carpet being cleaned 

Possible cause

Possible solution

• Hose clogged
• 

Remove hose and tools; remove 

obstruction

• Hose connector inserted incorrectly
• 

Re-insert hose connector properly

Possible cause

Possible solution

• Incorrect carpet height setting
• 

Move nozzle control knob to a 

higher setting

Problem: Cleaner won’t run

Problem: Cleaner won’t pick up

Problem: Cleaning tools won’t pick up

Problem: Cleaner hard to push

To obtain approved service and genuine
parts, locate the nearest 

Pacific Floor

Warranty Service Dealer 

by checking

the Yellow Pages under “Vacuum Clean-
ers - Household”.

If further assistance is needed, 

con-

tact Pacific Floor, 2259 Sheridan,
Muskegon, Michigan 49442
Phone: (800) 968-1332

www.nextwaveofclean.com

Always identify your cleaner by the

complete 

model number when request-

ing information or ordering parts. (The
model number appears on the bottom of
the cleaner.)

Summary of Contents for My Vac














Reviews: