Pacific Yurts 20' Yurt Setup Manual Download

Page: 17 / 62

Set Up Manual for 20

′

, 24

′

, & 30

′

Yurts

Securing Tension Cable

To eliminate the possibility of the tension cable coming out of the rafter notch a screw will need to be installed into

the predrilled hole on the underside of the rafter.

(See Diagram VI)

This secures the rafter end onto the cable

. Do

not substitute longer screws for those provided.

When installing the screw, install it only deep enough to make the head of the screw flush with the bottom of the

rafter.

If installed too deeply it is possible to drive the screw through the rafter and damage the top

cover. Note:

The rafters over the door(s) will not need these screws because they will be fastened to the door

frame.

Ring-to-Rafter Brackets

Diagram V:

Center Ring

Rafter

Ring-to-Rafter

Bracket

Rafter

Ring-to-Rafter

Bracket

Diagram V

Side View

Top View

Ring-to-Rafter

Bracket

Ring-to-Rafter

Bracket

Ring-to-Rafter

Bracket

Securing Tension Cable

Diagram VI:

Diagram VI

Summary of Contents for 20' Yurt































































Search results

Summary of Contents for 20' Yurt

Reviews:

Related manuals for 20' Yurt

Brands by name

Popular brands

Pacific Yurts 20' Yurt, Setup Manual

Search results

Summary of Contents for 20' Yurt

Reviews:

Related manuals for 20' Yurt

Brands by name

Popular brands