Pacific energy trenton A series Installation And Operating Instructions Manual Download Page 17 | Manualshive

Page: 17 / 40

Pacific energy trenton A series Installation And Operating Instructions Manual Download Page 17

17

TRNT.BODYA

5055.45-A 021115-40

Installer information

Trenton Co-Axial Venting Chart

30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10

9
8
7
6
5
4
3
2
1

1

2

3

4

5

6

7

8

9

10

11

12

13

14

VENTING HORIZONTAL RUN

VE

NT

ING

VE

RT

IC

AL

RI

SE

NO VENTING OPTION

VENTING ENVELOPE

NO VENTING OPTION

Note: The vent must

not exceed a total

length of 30 feet.

Any combination of

rise and run may be

used but must be

constrained to the

boundaries of this

chart. A Maximum of

three (3) 90° elbows

may be used. Only

one (1) 90° elbow or

combination of other

elbows equaling

90° can be used

without reducing

horizontal run. For

each additional

90° elbow, or an

equal combination

of elbows, reduce

horizontal vent run

by 2 feet. Ensure

vent pipe is properly

supported.

Damper Note:

The damper position

is factory set to the

closed position. Every

venting configuration

is different, and

the damper setting

may need slight

adjustment.

(See page 31 for

damper adjustment).

Figure 26:

Trenton Co-axial venting chart.

«
...
15
16
17
18
19
...
»

Summary of Contents for trenton A series









































Reviews:

No comments