manualshive.com logo in svg

Pacific energy NEO 1.6 INSERT, Nstallation And Operating Instructions, Page: 2 / 24

Share
Download
Pacific energy NEO 1.6 INSERT Nstallation And Operating Instructions Download Page 2

2  

040515-24

©PACIFIC ENERGY FIREPLACE 
PRODUCTS LTD.

PLEASE SAVE THESE INSTRUCTIONS

This manual describes the installation and operation of the Pacifi c Energy, NEO 1.6 Freestanding wood heater. This 
heater meets the 2015 U.S. Environmental Protection Agency's crib wood emission limits for wood heaters sold 
after May 15, 2015. Under specifi c test conditions this heater has been shown to deliver heat at rates ranging from 
9,200 to 34,800 Btu/hr.

NOTE: WE STRONGLY RECOMMEND THAT SMOKE AND CARBON MONOXIDE DETECTORS BE INSTALLED IN THE 
AREA WHERE THE HEATER IS TO BE INSTALLED.

If smoke detectors have been previously installed, you may notice that they are operating more frequently. This may be due 
to curing of stove paint or fumes caused by accidentally leaving the fi re door open. Do not disconnect the detectors. 

SAFETY NOTICE:  If this stove is not properly installed, a house fi re may result.  For your safety, follow the installa-
tion instructions.  Contact local building or fi re officials about restrictions and installation inspection requirements 
in you area.

Please read this entire manual before you install and use your new room heater.  Failure to follow instructions may result in 
property damage, bodily injury, or even death.

Contents

Safety .................................................................................................................... 3

Chimney Smoke and Creosote Formation .......................................................................... 3
Chimney Fires ..................................................................................................................... 3
In Case of a Chimney Fire .................................................................................................. 3
Avoiding a Chimney Fire ..................................................................................................... 3

Operation .............................................................................................................. 4

Wood Selection................................................................................................................... 4
How to Test Your Wood ....................................................................................................... 4
Lighting a Fire ..................................................................................................................... 4
Normal Operation ............................................................................................................... 4
Restarting After Extended or Overnight Burns .................................................................... 5
Over Firing .......................................................................................................................... 5
Heat Output Calculation ..................................................................................................... 5
Proper Draft ........................................................................................................................ 5
Ash Removal ...................................................................................................................... 5
Disposal of Ashes ............................................................................................................... 5
Storing Wood Beneath Unit ................................................................................................ 5

Maintenance ......................................................................................................... 6

Baffle Removal .................................................................................................................... 6

Maintenance Checks ........................................................................................... 7
Assembly .............................................................................................................. 8

Crate Removal .................................................................................................................... 8
Side Panel Installation ........................................................................................................ 8

NEO 1.6 Dimensions ............................................................................................ 8
Floor Protector ..................................................................................................... 9
Combustion Air .................................................................................................... 9
Residential Installation ..................................................................................... 10

Clearances ....................................................................................................................... 10
Chimney and Connector ................................................................................................... 10
Double-Wall Connector ..................................................................................................... 10
Single-Wall Connector ...................................................................................................... 10
Procedure ......................................................................................................................... 10

Mobile Home Installation .................................................................................. 11

Clearances ....................................................................................................................... 11
Procedure:......................................................................................................................... 12

Optional Blower ................................................................................................. 14

Blower Operation .............................................................................................................. 14
Optional Outside Air Adaptor ............................................................................................ 14

Troubleshooting ................................................................................................. 15

Replacement Parts - NEO 1.6 ........................................................................................... 16
Understanding & Operating Your Pacifi c Energy Stove ..................................................... 17

Warranty Information ......................................................................................... 19

Label ................................................................................................................................. 23

Summary of Contents for NEO 1.6 INSERT

























Reviews:

No comments