background image

General Information 
 

Introduction 

 

Thank you for purchasing the PACE SODRTEK

®

 model ST 125 Analog Desoldering System.  This 

manual will provide you with the information necessary to properly set up, operate and maintain the 
ST 125. 

 

The ST 125 system is available in either 115 VAC or 230 VAC versions, which incorporates a highly 
responsive SensaTemp (closed loop) control system providing up to 80 Watts of total power to a 
single output channel.  The 230 VAC version system bears the CE Conformity Marking, which 
assures the user that it conforms to EMC 89/336/EEC.   

 

The 115 VAC version systems conform to FCC Emission Control Standard, Title 47, Subpart B, Class 
A.  This standard is designed to provide reasonable protection against harmful interference when the 
equipment is operated in a commercial environment.  

 

 

Specifications 

 

System Power Source Power Requirements 

ST 125 

Operates on 97-127 VAC, 50/60Hz, 90 Watts maximum at 115 VAC, 
60Hz 

ST 125E 

Operates on 197-253 VAC 50/60Hz, 80 Watts maximum at 230 VAC, 
50Hz 

Temperature Specifications 

Handpieces 

Tip Temperature Range:  204 to 455°C (400 to 850°F) nominal. 

  Temperature 

Stability: 

 

±1.1°C 

(±2°F) at idle from set tip temp. 

 

NOTE:  

Actual minimum and maximum Operating Tip Temperatures may vary depending on   

Handpiece, Tip Selection and application. 

 

 

Vacuum And Air 

Measurements at front panel Vacuum and Controllable Pressure Ports.  
Vacuum Rise Time: ------- 150 ms average. 
Vacuum: ............................ 51 cm Hg. (20 in. Hg.) (nominal) 
Pressure: .......................... 1.44 Bar (21 P.S.I.) (nominal at MAX setting) 
Air Flow: ........................... 6 SLPM (0.22 SCFM) maximum

 

 

EOS/ESD Specifications 

 

The specifications shown below apply except on "Soft Ground Systems" which have a 1meg ohm 
current limiting resistance and a label placed on the power source front panel referring to EN 
100015-1. 

Tip-To-Ground Resistance:  Less than 2 ohms.

 

AC Leakage:  Less than 2 Millivolts RMS from 50Hz to 10MHz.

 

Transient Level:  Less than 500mV peak, out to 100MHz. 

 

 
 
 
 
 
 
 
 

©2004 PACE Inc., Annapolis Junction, Maryland 

Page 3 of 13 

All Rights Reserved 

Summary of Contents for SODRTEK ST 125














Reviews: