background image

 11

DISPLAY

DISPLAY

DISPLAY

DISPLAY
MESSAGE

MESSAGE

MESSAGE

MESSAGE

DESCRIPTION

DESCRIPTION

DESCRIPTION

DESCRIPTION

C-1 OR C-2

Indicates system is ready to process Digital Readout accuracy
calibration for a particular channel using the appropriate
calibration module.

CAL

Indicates that system is in the Calibration Mode.

E-5

Input to control circuitry unstable.  Indicates that no calibration
module is connected to the channel being calibrated or the
incorrect module has been inserted.

E-6

Loose connection.  Calibration input is out of range.  Normally
occurs if incorrect calibration module is inserted.

H-X
(X = 1 thru 9)

Indicates the Current Channel is ready to accept new Upper
Temperature Limit setpoint X (X times 100°F).

L-X
(X = 1 thru 9)

Indicates the Current Channel is ready to accept new Lower
Temperature Limit setpoint X (X times 100°F).

OFF

Setpoint for this channel is below Lower Temperature Limit
setpoint.

S--

Indicates that the Automatic Temperature Setback (and Power
Down) feature is disabled (turned off).

S-X

Indicates that the Automatic Temperature Setback (and Power
Down) feature is enabled (turned on) and will set each channels'
Set Tip Temperature back after X times 10 minutes of handpiece
inactivity (non-use).

---
(flashing)

Indicates that the system circuitry is proceeding with calibration
using the proper calibration module (C-1 or C-2).

Summary of Contents for 6993-0133













Reviews: