background image

Introduction 

Thank you for purchasing the PACE model PS-90 Soldering Irons. These irons should only be used with 
PACE SensaTemp compatible power supplies. This manual will provide you with the information 
necessary to properly set-up, maintain and operate the PS-90. 
  

Part Identification 

English  

1. Tip  
2. Heater Assembly  
3. Heater Set Screw  
4. Heater Retaining Nut  
5. Handle  
6. Power Cable  

 

 
 

English Language Safety Guidelines 

The following are safety precautions that personnel must understand and follow. 
1. Utilize all standard electrical safety precautions when using this or any other electrical equipment. 
2. Always use this handpiece (and system) in a well ventilated area. 
3. Do not leave the PACE system unattended when in use. 
4. Repair on this product should be performed by Qualified Service Personnel only. 

 

 

Set-Up 
 
Tip & Tool Stand 

The Tip & Tool Stand can be mounted to the power source. If the system will be placed on the workbench, this 
is recommended. If the power source is to be mounted under the workbench or shelf, the Tip & Tool Stand 
should not be mounted to the power source. 
 

1. To attach the stand to the power source: 

a) Insert the 2 Mounting Screws (head first) into the power 

source mounting slots (plastic case shown). Slide the screws 
toward the rear of power source. 

b) Place the Tip & Tool Stand beside the power source. Insert 

ends of the 2 Mounting Screws into the 2 Tip & Tool Stand 
mounting holes shown. 

c) Install a Thumb Nut onto the end of each Mounting Screw and 

tighten Thumb Nuts. 

 

2. Place the handpiece into its Tip & Tool Stand. 

 

w w w . e k t

2

. c o m

Summary of Contents for 5050-0530












Reviews: