Pace Technologies FEMTO 1500 Instruction Manual Download Page 7

Page: 7 / 105

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ▲

NSTRUCTION

ANUAL

3601 E. 34th St. Tucson, AZ 85713 USA Tel. +1 520-882-6598 Fax +1 520-882-6599 email: [email protected] Web: http://www.metallographic.com

Please read this instruction manual carefully and follow all installation, operating and safety guidelines.

NANO 1000T / FEMTO 1500

Polishing Head

1.3 Features and Benefits

Note:

Installation of the FEMTO 1500 /

NANO polishing base should be on a flat
sturdy surface, with easy access to drain,
water and electrical connections.

The

FEMTO 1500

is equipped with a 120 W

variable 0-200 rpm speed motor. The drive
mechanism is connected to the motor via a
maintenance-free anti-slip polychain.

The

FEMTO 1500

also has a lubricant

dispenser in addition to a high flow water
valve for hands free wet grinding with
abrasive papers and lubrication for polishing.

In addition, the

FEMTO 1500

can be operated

either automatically or independently with the
NANO polishing base.

Summary of Contents for FEMTO 1500










































































































Search results

Summary of Contents for FEMTO 1500

Reviews:

Related manuals for FEMTO 1500

Brands by name

Popular brands

Pace Technologies FEMTO 1500, Instruction Manual

Search results

Summary of Contents for FEMTO 1500

Reviews:

Related manuals for FEMTO 1500

Brands by name

Popular brands