manualshive.com logo in svg

Pace Edwards UltraGroove Electric KE2003, Installation Instructions Manual

Share
Download
Pace Edwards UltraGroove Electric KE2003 Installation Instructions Manual Download Page 1

Tools Required for Assembly 

 

 ...................................... 1 

Before You Start  .......................................................... 1 

Canister Drain Hole Locations ...................................... 1 

STEP 1:  Remove From Packaging, and  

                Review Contents

 

 .......................................... 1 

STEP 2:  Install Wiring Harness  ................................... 2 

STEP 3:  Positioning Canister  ...................................... 2 

STEP 4:  Installing Rails ............................................... 3 

STEP 5:  Installing The Top Cover

 ................................ 

4 

STEP 6:  Installing The Clamp Extensions ................... 5 

STEP 7:  Installing The Clamps .................................... 6

 

STEP 8:

  

Installing Tailgate Draintubes  ....................... 8 

STEP 9:

 

Lubricating and Placing the Sweap Seals ....... 8 

STEP 10: Connecting the Electronics  .......................... 8 

STEP 11: Installing Canister Drain Tubes……………...9 

STEP 12: Release Handle Instructions………………..10 

Maintenance ……………………………………………..10 

Release Handle Assembly Maintenance…...…………10 

Warranty Statement…………………………………......11

 

KET1-1707

 

INSTALLATION INSTRUCTIONS 

TOYOTA TUNDRA 

      

TABLE OF CONTENTS

 

Electric Retractable Tonneau Covers 

UltraGroove Electric

™ 

 

(800) 338-3697 

www.paceedwards.com

 

Pace Edwards Company 

2400 Commercial Blvd. 

Centralia WA 98531

 

Summary of Contents for UltraGroove Electric KE2003













Reviews:

No comments

Brands by name

Popular brands

Load more brands