PAC BCI-CH41 Quick Start Manual Download Page 3

Rev. 022615

Page 3

BCI-CH41

Navigation Unlock & Reverse Camera Input

 Interface for Chrysler/Dodge/Jeep/Ram Vehicles

Pacific Accessory Corporation

To Access the Settings Menu

1. Place the MFD into the mode that displays the radios text.

2. Press and hold the “VR” button on the SWC for approximately 8 seconds (see Fig. D or Fig. E)

3. “BCI Menu” will be displayed on the MFD in the gauge cluster.

4. Use  the  up/down  buttons  on  the  back  of  either  side  of  the  steering  wheel  (Fig.  F)  to  scroll

through and make selections in the menus. Press the center button will to turn options on/off.

5. The list of available options are:

A.  Nav Unlock - This allows features that are normally blocked while the vehicle is in motion

to be unlocked.

B.  Remote Start Restore Climate Settings - restores the climate controls to the last known 

setting on remote start. Without this feature the climate controls do not go to last known 

setting until a door is opened.

C.  Add  RevCam  (only  available  when  the  vehicle  is  not  equipped  with  a  factory  reverse 

camera)  - This  will  activate  the  reverse  camera  input  feature  of  the  radio. This  feature 

comes default set to On.

D.  Vid in Aux - This will automatically switch to the reverse camera whenever the radio is put 

into Aux mode. (Nav Unlock 

MUST

 be activated)

E.  12v in rev/12v in AUX/12v in Acc - This sets the interfaces red output wire behavior to trigger 

either a reverse camera, a video switcher or be an ACC output whenever the vehicle is on.

F.  Swap Source/Preset SWC - This will allow you to swap the Source and Preset SWC around.
G.  Swap Volume/Seek SWC - This will allow you to swap the Volume and Seek SWC around.
H.  Eco Memory (only available in vehicles equipped with an Eco Mode button) - This will force 

the vehicle to remember the Eco Mode setting once the vehicles key has been cycled

I.  Exit Menu - Saves all settings and exits the menu.

6. Once finished, scroll to the “Exit Menu” section and press the preset button or wait 30 seconds

for the menu to timeout.

Operation - All Other Vehicles

Fig. D

Fig. E

Fig. F

In these vehicles the BCI-CH41 offers even more features. All of these features can be turned on/off through a menu accessible 

through the SWC. The BCI-CH41 comes with all features except reverse camera input set to off by default.

To Activate the Nav Unlock feature

1. Press and hold the center button on the back right of the steering wheel for at least four seconds, then release.

2. The MFD in the cluster will display “Confirm Safe Passenger Use”.

3. Once the text is finished scrolling, press the same button again within 5 seconds to acknowledge “safe use”, 

agreeing that

use will be performed only by the passenger whenever the vehicle is in motion

, and activate the BCI-CH41.

4. The MFD will display “Acknowledged”.

5. To de-activate the BCI-CH41 simply press and hold the same button for at least four seconds and then release.

6. The MFD will display “NU Deactivated”
You can also force the reverse camera image at any time by pressing and holding the center button on the back left of the steering 

wheel for 4 seconds until “Rev Camera On” is displayed on the MFD. The Nav Unlock feature is now deactivated.

DISCLAIMER: Under no circumstances shall the manufacture or the distributors of the BCI-CH41 be held liable for claims of any loss 

or damage, consequential, direct or indirect, arising from the sale, installation, or use of the BCI-CH41. The manufacture and its dis-

tributors will not, nor will they authorize any representative or any other individual, to assume obligation or liability in relation to the 

BCI-CH41 other than its replacement.
AGREEMENT: End user agrees to use this product in compliance with the instructions and terms of use above and with all State and 

Federal laws. PAC provides instructions and safety warnings with respect to this product and disclaims all liability for any use not in 

conformity with those instructions or other misuse of its product. If you do not agree, please discontinue use immediately and return 

product to place of purchase. This product is intended for off-road use and passenger use only.

Get top quality PAC products on our website.   

                Accept no compromises, choose only quality OE integration interfaces.

Reviews: