P3 International V3 Configuration Manual Download Page 7 | Manualshive

Page: 7 / 13

background image

bSt.6 = OBD2 rescaled MAP reading for 6th gen Camaro (all models)

bSt.7 = Future use

bSt.8 = Alternate digital boost for BMW N63

bSt.9 = Future Use

Analog Input 1 (

brown

wire on P3 V3 main harness)

A1.n = Analog input disabled

A1.Y = Opens sub-menu for manually configuring sensor input values (see "Analog Inputs"
section for details)

A1.EC = Pre-configured setting for P3 ESVA Ethanol content output (brown wire on P3 ESVA)

A1.Ft = Pre-configured setting for P3 ESVA Fuel temp output (blue wire on P3 ESVA)

A1.LC = Pre-configured setting for LC-2 wideband o2 output (yellow wire on LC-2 wideband

A1.PS = Pre-configured setting for P3 Pressure Sensor (green wire on P3 Pressure Sensor)

Analog Input 2 (

blue

wire on P3 V3 main harness)

A2.n = Analog input disabled

A2.Y = Opens sub-menu for manually configuring sensor input values (see "Analog Inputs"
section for details)

A2.EC = Pre-configured setting for P3 ESVA Ethanol content output (brown wire on P3 ESVA)

A2.Ft = Pre-configured setting for P3 ESVA Fuel temp output (blue wire on P3 ESVA)

A2.LC = Pre-configured setting for LC-2 wideband o2 output (yellow wire on LC-2 wideband)

A2.PS = Pre-configured setting for P3 Pressure Sensor (green wire on P3 Pressure Sensor)

Boost Units Setting

b.PSI = Boost read in PSI

b.bAr = Boost read in BAR

Boost Pressure Resolution

Pr0.1 = Boost shown down to 1/10th units

«
...
5
6
7
8
9
...
»

Summary of Contents for V3














Reviews:

No comments

Related manuals for V3

Brand: M3S Pages: 40

Brand: Sabre Pages: 13

Brand: RADWAG Pages: 176

Commissioner dali

Brand: Artistic License Pages: 26

Friendly Digital Piano Forte PV35

Brand: Kawai Pages: 102

C100L-L-DD-LE-5-OV1-SV1-PV1C-V1-S1

Brand: Sierra Pages: 55

Brand: Amrutha Technologies Pages: 22

Brand: Straightpoint Pages: 24

Brand: DIALAB Pages: 20

EnviroAlert EA200

Brand: Winland Pages: 3

Brand: PHYWE Pages: 6

Brand: Eaton Pages: 13

Brand: Bamo Pages: 2

Druck DryTC 165

Brand: Baker Hughes Pages: 130

Brand: Hanna Instruments Pages: 24

Brand: Medical International Research Pages: 46

Class 3400 Meter

Brand: E-Mon Pages: 20

Brand: Astute Medical Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands