background image

Troubleshooting:   

Item

 

Symptoms

 

Action

 

Description

 

1   

LCD display is flashing   

Press any key   

1.  This  is  normal  operation  after 
you plug the unit into a wall outlet. 
2.  AC  power  to  the  unit  has been 
interrupted.   

2   

Over  Current  icon  on  LCD 
is  flashing  and  audible 
alarm is sounded, output is 
off  and  the  red  LED  in  the 
OFF key is flashing   

Press  Reset  key  (OFF  key),  check  & 
remove the appliance which is drawing 
over  current  or  reduce  the  number  of 
appliances connecting to the unit or set 
a larger Max. Amps setting. Press ON 
key to restart   

This is the over current protection 
function indicating  the total power 
consumption  is  larger  than  the 
Max. amps setting value or that an 
appliance  is  drawing  too  much 
current.   

3   

Over  Load  icon  on  LCD  is 
flashing  and  audible  alarm 
is  sounded,  output  is  off 
and  the  red  LED  in  the 
OFF key is flashing   

Press  Reset  key  (OFF  key),  check  & 
remove the appliance which is drawing 
an over load of current. Press ON key 
to restart.   

This  is  the  over  load  protection 
function.  Indicates  that  attached 
appliances  could  have  a  short 
circuit.   

4   

Abnormal  Voltage  icon  on 
LCD 

is 

flashing 

and 

audible  alarm  is  sounded, 
output  is  off  and  the  red 
LED  in  the  OFF  key  is 
flashing   

The unit will restart automatically when 
the  AC  power  line  voltage  returns  to 
normal  voltage  range.  If  condition 
persists call a qualified technician.   

This  is  the  abnormal  voltage  (too 
high  or  too  low)  protection 
function.   

5   

No  Load  icon  on  the  LCD 
display flashes   

The  unit  will  power  on  automatically 
when the load returns   

This  is  the  no  load  protection 
function  to  reduce  the  chance 
electrical shock or damage   

6   

No  Load  icon  continues  to 
flash  when  appliances  are 
connected and turned on   

Increase  the  number  of  connected 
appliances   

The minimum watt detected by the 
unit is 0.2W. Some few appliances 
may  have  a  stand-by  mode  that 
consume less than 0.2W.   

7   

Replace  icon  on  the  LCD 
flashes   

Request technical support   

This  is  a  self  diagnostic  function 
for  the  main  power  relay  switch. 
This  indicates  the  relay  is  non 
functional.   

8   

Ground  OK  &  Wiring  OK 
icon on the LCD are turned 
off   

Ask for a qualified electrical technician 
to  check  your  house  wiring  and 
grounding   

These icons  turning  off indicate  a 
wiring defect   

9   

Surge OK icon on the LCD 
is turned off   

Request technical support   

This  is  a  self  diagnostic  function 
for  the  surge  protector  MOV 
indicating 

the 

MOV 

is 

non 

functional   

10   

No  display  in  the  LCD,  no 
response  from  pressing 
keys   

1.  Check that the unit connected to an 

energized AC wall outlet. 

2.  Check if the NFB (No Fuse breaker) 

is ejected from the body of the unit. 
If  yes,  disconnect  any  defective 
appliances from the unit, then press 
the NFB button again to restart. 

a.  3. Request technical support   

When no AC power is applied or if 
the NFB is ejected the unit will not 
function.   

Shop for P3 products online at:

1.877.766.5412

www.

PowerMeterStore

.ca

Summary of Contents for Kill A Watt PS













Reviews: