background image

EN

07

Trike Launch Assist System

The  risers  are  equipped  with  an  attachment  point  for  the  trike  launch  assist  system.  This 

system shortens the A risers to help with the first phase of the inflation (when the canopy is 

still behind the trike/pilot). 

The A-Assist needs to be adjusted so that once the wing is inflated above the head it is no 

longer under tensioning and inadvertently pulling the A risers. 

The length of the system can be adjusted to suite conditions or taste. If the canopy is inflating 

too fast, the system should be  lengthened to reduce the speed, whereas if the canopy rises 

too slowly the system should be reduced in length. It is not necessary to hold the A risers 

whilst launching with the trike assist system. The system is part of the trike construction so 

please refer to the trike manual for more information.

Spreader bars / Accessories

The MagMax 2 is delivered as standard without any special equipment for tandem flying. 

All suitable accessories such as tandem spreader bars, tandem roll bar etc are specific to a 

paramotor / trike unit and needs to be provided by the paramotor / trike manufacture. It is 

the pilot’s responsibility to make a hang test and to ensure the set up is well adjusted and 

balanced. 

Summary of Contents for MAGMAX 2



































Reviews: