background image

IN ORDER TO MAKE A CLAIM UNDER THIS 

WARRANTY YOU MUST RETURN THE PRODUCT 

TO YOUR NEAREST BUNNINGS WAREHOUSE WITH 

YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO 

RETURNING YOUR PRODUCT FOR WARRANTY 

PLEASE TELEPHONE OUR CUSTOMER SERVICE 

HELPLINE:

Australia 1800 069 486
New Zealand 0508 069 486

3 YEAR REPLACEMENT WARRANTY

Your product is guaranteed for a period of 

36 months from  

the original date of purchase 

and is

 

intended for DIY (Do It 

Yourself) use only.

 

If a product is defective it will  

be replaced in accordance with the terms of this warranty.  
Warranty excludes consumable parts, for example:

WARNING

The following actions will result in the warranty being void.

•   If the tool has been operated on a supply voltage other  

than that specified on the tool.

•   If the tool shows signs of damage or defects caused  

by or resulting from abuse, accidents or alterations.

•   Failure to perform maintenance as set out within the 

instruction manual.

•   If the tool is disassembled or tampered with in any way.
•  Professional, industrial or high frequency use.

WARRANTY

TO ENSURE A SPEEDY RESPONSE PLEASE 

HAVE THE MODEL NUMBER AND DATE OF 

PURCHASE AVAILABLE. A CUSTOMER SERVICE 

REPRESENTATIVE WILL TAKE YOUR CALL  

AND ANSWER ANY QUESTIONS YOU MAY  

HAVE RELATING TO THE WARRANTY POLICY  

OR PROCEDURE.

OZITO 

Australia/New Zealand (Head Office)

 

1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.

The benefits provided under this warranty are in addition  
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded  
at law. You are entitled to a replacement or refund for a major 
failure and for compensation for any other reasonably foreseeable 
loss or damage. You are also entitled to have the goods repaired  
or replaced if the goods fail to be of acceptable quality and the 
failure does not amount to a major failure. 
Generally you will be responsible for all costs associated with  
a claim under this warranty, however, where you have suffered  
any additional direct loss as a result of a defective product you  
may be able to claim such expenses by contacting our customer 
service helpline above.

1114

Summary of Contents for UMS-1810 S











Reviews: