background image

GB

- 8 -

Please note that our equipment has not been de-

signed for use in commercial, trade or industrial 

applications. Our warranty will be voided if the 

machine is used in commercial, trade or industrial 

businesses or for equivalent purposes.

The equipment is to be operated only with suita-

ble saw blades (saw blades made of HM or CV) 

It is prohibited to use any type of HSS saw blade 

and cutting-o

  wheel.

To use the equipment properly you must also 

observe the safety information, the assembly 

instructions and the operating instructions to be 

found in this manual.

All persons who use and service the equipment 

have to be acquainted with these operating 

instructions and must be informed about the 

equipment‘s potential hazards. It is also imperati-

ve to observe the accident prevention regulations 

in force in your area. The same applies for the 

general rules of health and safety at work.

The manufacturer will not be liable for any chan-

ges made to the equipment nor for any damage 

resulting from such changes. Even when the 

equipment is used as prescribed it is still impossi-

ble to eliminate certain residual risk factors.

The following hazards may arise in connection 

with the machine‘s construction and design:

• 

Contact with the saw blade in the uncovered 

saw zone.

• 

Reaching into the running saw blade (cut 

injuries).

• 

Kick-back of workpieces and parts of work-

pieces.

• 

Saw blade fracturing.

• 

Catapulting of faulty carbide tips from the saw 

blade.

• 

Damage to hearing if essential ear-muffs are 

not used.

• 

Harmful emissions of wood dust when used 

in closed rooms.

4. Technical data

 AC motor  ........................................ 230V ~ 50Hz
Power P  .................................... 800 W S2 10 min
Idle speed n

0

  ...................................... 2950 min

-1

Cutting-o

  wheel  ............  Ø 200 x Ø 16 x 2.4 mm

Number of teeth  .............................................  24
Table size  .....................................  500 x 335 mm
Cutting height max.  .........................  45 mm / 90°
.........................................................  35 mm / 45°
Extractor socket  ................................... Ø 36 mm
Weight  ........................................  approx. 12.3 kg 
Thickness of the splitter:  ......................... 2.2 mm

Load factor:

A load factor of S2 10 min (intermittent periodic 

duty) means that you may operate the motor 

continuously at its nominal power level (800 

W) for no longer than the time stipulated on the 

speci

fi

 cations label (10 min). If you fail to observe 

this time limit the motor will overheat. During the 

OFF period the motor will cool again to its starting 

temperature.

Danger! 

Sound and vibration

Sound and vibration values were measured in 

accordance with EN 61029.

Operation

L

pA

 sound pressure level  ..................... 96,6 dB(A)

K

pA

 uncertainty  .............................................3 dB

L

WA

 sound power level   ..................... 109,6 dB(A)

K

WA

 uncertainty .............................................3 dB

 The quoted values are emission values and not 

necessarily reliable workplace values. Although 

there is a correlation between emission and im-

mission levels it is impossible to draw any certain 

conclusions as to the need for additional precau-

tions. Factors with a potential in

fl

 uence on the ac-

tual immission level at the workplace include the 

duration of impact, the type of room, and other 

sources of noise etc., e.g. the number of machi-

nes and other neighboring operations. Reliable 

workplace values may also vary from country to 

country. With this information the user should at 

least be able to make a better assessment of the 

dangers and risks involved.

Anl_TSB_0808U.indb   8

Anl_TSB_0808U.indb   8

07.04.2017   10:03:11

07.04.2017   10:03:11

Summary of Contents for TSB-0808U

















Reviews: