background image

ONLINE MANUAL

Scan this QR Code with your 

mobile device to take you to 

the online manual.

1  Rip Fence

2  Mitre Guide
3  Blade Guard
4  Blade Guard Mounting Bolt
5  Saw Blade
6  Push Stick Holder

7  Rip Fence Lock Knob
8  On/Off Safety Switch
9  Bevel Lock Knob
10 Bevel Angle Gauge
11 Saw Table

TABLE SAW 

KNOW YOUR PRODUCT

1.  ASSEMBLY

SETUP & PREPARATION

WARNING!:

 ENSURE THE TOOL IS DISCONNECTED  

FROM THE POWER SUPPLY BEFORE ASSEMBLY

12 Push Stick

13 Blade Spanners x 2

1   Remove the chip bin 

cover by removing the 2 

fixing screws either side.

3   Remove the outer 

flange.

Note:

 Ensure the mounting 

flange is clean and free of 

grease prior to fitting the 

blade.

2   Remove the blade 

nut by rotating anti-

clockwise using the 

supplied spanners. 

4   Fit the blade onto the 

spindle, ensuring the 

blade direction matches 

the directional arrows 

on the housing.

5   Refit the outer flange 

and blade nut. Tighten 

using the supplied 

spanners to secure the 

blade.

Fitting the Blade

6

12

13

1

2

3

4

5

7

8

9 10

11

REPLACEMENT BLADES: 

You will find a selection of blades available from the Tool Shop 

at Bunnings Warehouse. 

If the required saw blade size is not available at Bunnings, 

this part can be ordered from the Special Orders Desk at 

your local Bunnings Warehouse.

Summary of Contents for tsb-0808







Reviews: