Power tools that are no longer usable should not be disposed of with
household waste but in an environmentally friendly way. Please recycle
where facilities exist. Check with your local council authority for recycling
advice.
Recycling packaging reduces the need for landfill and raw materials.
Reuse of recycled material decreases pollution in the environment. Please
recycle packaging where facilities exist. Check with your local council
authority for recycling advice.
DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
BATTERY & CHARGER SAFETY WARNINGS
TROUBLESHOOTING
Spare parts can be ordered from the Special Orders
Desk at your local Bunnings Warehouse.
For further information, or any parts not listed here,
visit www.ozito.com.au or contact Ozito Customer
Service:
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR
YOUR BATTERY CHARGER.
1.
Before using the charger read all instructions and cautionary markings on the charger, battery pack
and the product using the battery pack.
2.
This charger is not intended for any uses other than charging rechargeable batteries. Any other use
may result in risk of fire, electric shock or electrocution.
3.
Do not place any object on top of the charger or place the charger on a soft surface that may result
in excessive internal heat. Place the charger in a position away from any heat source.
4.
To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when
disconnecting the charger.
5.
Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise subjected
to damage or stress.
6.
An extension cord should not be used unless absolutely necessary. Use of an improper extension cord
could result in the risk of fire, electric shock or electrocution.
7.
Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in
any way. Have it checked by an electrician or power tool repairer.
8.
Do not disassemble charger. Take it to an electrician or power tool repairer when service or repair is
required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.
9.
To reduce risk of electric shock, unplug the charger from the outlet before attempting any cleaning.
Removing the battery pack will not reduce this risk.
10.
Never attempt to connect 2 chargers together.
11.
DO NOT store or use the tool and battery pack in locations where the temperature may reach or exceed
40ºC (such as inside sheds or metal buildings in summer).
12.
The charger is designed to operate on standard household electrical power (240 volts). Do not
attempt to use it on any other voltage!
13.
The battery pack is not fully charged out of the carton. First read the safety instructions and then
follow the charging notes and procedures.
14.
The longest life and best performance can be obtained if the battery pack is charged when the air
temperature is between 18 - 24ºC. Do not charge the battery pack in an air temperature below 10ºC
or above 40ºC. This is important and will prevent damage to the battery pack.
15.
Do not incinerate the battery pack even if it is seriously damaged or is completely worn out. The battery
can explode in a fire.
16.
Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or
cracks, immediately discontinue use and do not recharge.
17.
During charging, the battery must be placed in a well ventilated area.
LED lights do not illuminate on charger
Check the charging adaptor is securely plugged into the wall out let.
Check the battery is firmly connected to the charging cradle.
Check that the charging jack is securely connected to the charging cradle.
The battery has a short run time
Ensure the battery is properly charged. It will take 4-5 charging cycles before the battery
reaches optimum charge and run time. On the initial charge, the battery requires 5 hours
of charging. Subsequent charging only requires 3-5 hours.
Sparking visible through the housing vents
A small amount of sparking may be visible through the housing vents.
This is normal and does not indicate a problem.
Variable speed trigger is locked
Ensure that the forward / reverse lever is in the correct position; pressed left for
forwards direction, pressed right for backwards direction. If it is in between the two
settings the variable speed trigger will be locked.
The Impact Driver is stripping the screw head
Ensure you are not applying to much force to the screw. Decrease the force by using a
slower trigger speed.
MAINTENANCE
• After each use, blow air through the tool housing to ensure it is free from all dust,
dirt, etc. Build up of dust, dirt particles may cause the tool to overheat and shorten
the life of the tool.
• If the housing of the impact driver requires cleaning, do not use solvents but a moist
soft cloth or soft brush only.
• Never let any liquid get inside the tool, never immerse any part of the tool into liquid.
• When not in use, the impact driver should be stored in a dry, frost free location not
within the reach of children.
WARNING!
ALWAYS ENSURE THE TOOL HAS
COMPLETELY STOPPED AND THE BATTERY IS
REMOVED PRIOR TO ANY MAINTENANCE.
Note: Ozito Industries will not be responsible for any damage or injuries caused by
the repair of the impact driver by an unauthorised person or by mishandling of the
impact driver.
Battery protection system
The tool is equipped with the battery protection system, which helps to ensure a long service
life.
The output power automatically cuts off during operation when the tool and/or battery are
placed under the following situations:
• When the tool is overloaded:
If this occurs, release the trigger switch and remove causes of overload, then pull the
switch trigger again to restart.
• When the remaining battery capacity becomes low:
Recharge the battery pack.
Warning
Read instruction manual
ø
Diameter
mA
Milliamperes
Recycle battery
Do not put in the rubbish
Polarity
Do not incinerate
Do not get battery wet
Thermal cut-out protection
Transformer Energy
Rating (MEPS)
Double insulated
/min
Revolutions or reciprocation per minute
Ah
Amp hour
Indoor use only
Lithium Ion battery
Do not use or store battery in
temperatures exceeding 50ºC
Regulatory Compliance
Mark (RCM)
Nm
Newton Meters
n
o
No load speed
V
Volts
Hz
Hertz
ac/~
Alternating current
W
Watts
Direct current
dc/
