5. TRIMMING & EDGING
OPERATION
Trimming
Edging
Move the grass trimmer from side to side as
you walk forward, holding it at an angle of
approx. 30° (Light cuts are better than heavy
cuts as they allow the cut grass to fall away
from the cutting head).
Place the edging guide along the ground
and slide the grass trimmer along the edge
of the path.
30°
WARNING!
ALWAYS ENSURE THE TOOL HAS
COMPLETELY STOPPED AND THE BATTERY IS
REMOVED PRIOR TO ANY MAINTENANCE.
Replacing the Spindle Plate
1. Unscrew the countersunk head
screw in the centre of the spindle
plate, rotate anti-clockwise to
remove. Once removed put aside
for re-assembly.
2. Lift off the spindle plate.
3. Mount and fasten the new
spindle plate.
MAINTENANCE
Problem
Cause
Remedy
Trimmer is not
starting
Possible clogging
Clean the cutter head of any grass.
Battery is low in charge
Charge battery
Battery not inserted properly
Insert battery pack correctly
T
rimmer is not
operating at full
capacity
Possible clogging
Clean the cutter head of any grass.
Cutting tall grass at ground
level.
Make several passes from top down.
Motor stops while
operating
Battery has no power
Charge battery
Grass wraps around
the shaft and
trimmer head.
Cutting tall grass at ground
level.
Make several passes from top down.
Spare parts can be ordered from the Special Orders Desk at your local Bunnings Warehouse or
Homebase store.
For further information, or any parts visit
www.ozito-diy.co.uk or contact Ozito Customer Service:
Great Britain: 0151 294 4488
Ireland: 1850 882711
E-mail: [email protected]
Troubleshooting
Service Information
Please note that the following parts of this product are subject to normal or natural wear and
that the following parts are therefore also required for use as consumables.
* Not necessarily included in the scope of delivery!
Category
Example
Wear parts*
Blade head, Battery
Consumables
Blade
Missing parts
•
Keep ventilation slots of the trimmer clean at all times. Periodically clean out the grass from the cutting
head and the rim of the blade guard to ensure efficient operation at all times.
•
After each use, blow air through the tool housing to ensure it is free from all dust, dirt, etc. Build up of
dust, dirt particles may cause the tool to overheat and shorten the life of the tool.
•
If the housing of the trimmer requires cleaning, do not use solvents but a moist soft cloth or soft brush
only.
•
Never let any liquid get inside the tool, never immerse any part of the tool into liquid.
• No lubrication is necessary as the tool has sealed bearings.
•
When not in use, the grass trimmer should be stored in a dry, frost free location not within the reach of
children.
Note: Ozito Industries will not be responsible for any damage or injuries caused by the repair of the grass
trimmer by an unauthorised person or by mishandling of the grass trimmer. This tool is designed for DIY use -
use in commercial or industrial environments will void the warranty.
Spare Parts
MAINTENANCE cont.
Gao/Product-Management
Weichselgartner/General-Manager
explains the following conformity according to EU directives and norms for
the following product
Cordless Grass Trimmer PXCLTK-018U / Eco Charger PXCG-120U (Ozito)
2014/29/EU
2005/32/EC_2009/125/EC
2014/35/EU
2006/28/EC
X
2014/30/EU
2014/32/EU
2014/53/EC
2014/68/EU
90/396/EC_2009/142/EC
89/686/EC_96/58/EC
X
2011/65/EU
X
2006/42/EC
Annex IV
Reg. No.:
X
2000/14/EC_2005/88/EC
Annex V
X
Annex VI
Noise: measured L
WA
= 84,3 dB (A); guaranteed L
WA
= 94 dB (A)
P = KW; L/Ø = cm
2004/26/EC
Emission No.:
Standard references: EN 60335-1; EN 60335-2-29; EN 50636-2-91; EN 62233
EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3
Landau/Isar, den 21.07.2017
First CE: 16
Archive-File/Record:
NAPR016849
Art.-No.:
34.111.89
I.-No.: 11027
Documents registrar:
Robert Gehard
Subject to change without notice
Wiesenweg 22, D-94405 Landau/Isar
ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar
