![background image](http://html1.mh-extra.com/html/ozito/pxcgtas-018/pxcgtas-018_instruction-manual_1666860005.webp)
DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
TROUBLESHOOTING
Power tools that are no longer usable should not be disposed of with
household waste but in an environmentally friendly way. Please recycle
where facilities exist. Check with your local council authority for recycling
advice.
Recycling packaging reduces the need for landfill and raw materials. Reuse
of recycled material decreases pollution in the environment. Please recycle
packaging where facilities exist. Check with your local council authority for
recycling advice.
Spare parts can be ordered from the Special Orders
Desk at your local Bunnings Warehouse.
For further information, or any parts not listed here,
visit www.ozito.com.au or contact Ozito Customer
Service:
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
Problem
Cause
Remedy
Trimmer is not
starting
Possible clogging
Clean the cutter head of any grass.
Battery is low in charge
Charge battery
Battery not inserted
properly
Insert battery pack correctly
Trimmer is not
operating at full
capacity
Possible clogging
Clean the cutter head of any grass.
Cutting tall grass at ground
level.
Make several passes from top down.
Motor stops
while operating
Battery has no power
Charge battery
Grass wraps
around the shaft
and trimmer
head.
Cutting tall grass at ground
level.
Make several passes from top down.
Wear goggles and ear muffs
Read instruction manual
90
Decibel level
Do not use in the rain or leave the grass trimmer outdors while raining
Regulator compliance mark
Warning!
The equipment continues to rotate!
Keep all other persons away from the danger zone.
MAINTENANCE
• Keep ventilation slots of the trimmer clean at all times. Periodically clean out the grass
from the cutting head and the rim of the blade guard to ensure efficient operation at all
times.
• After each use, blow air through the tool housing to ensure it is free from all dust, dirt,
etc. Buildup of dust, dirt particles may cause the tool to overheat and shorten the life
of the tool.
• If the housing of the trimmer requires cleaning, do not use solvents but a moist soft
cloth or soft brush only.
• Never let any liquid get inside the tool, never immerse any part of the tool into liquid.
• No lubrication is necessary as the tool has sealed bearings.
• When not in use, the grass trimmer should be stored in a dry, frost free location not
within the reach of children.
Note: Ozito Industries will not be responsible for any damage or injuries caused by the
repair of the grass trimmer by an unauthorised person or by mishandling of the grass
trimmer. This tool is designed for DIY use - use in commercial or industrial environments
will void the warranty.
Replacing the Spindle Plate
WARNING!
ALWAYS ENSURE THE TOOL HAS
COMPLETELY STOPPED AND THE BATTERY IS
REMOVED PRIOR TO ANY MAINTENANCE.
1. Unscrew the countersunk
head screw in the centre
of the spindle plate, rotate
anti-clockwise to remove.
Once removed put aside for
re-assembly.
2. Lift off the spindle plate.
3. Mount and fasten the new
spindle plate.
Battery protection system
The tool is equipped with the battery protection system, which helps to ensure a long service
life.
The output power automatically cuts off during operation when the tool and/or battery are
placed under the following situations:
• When the tool is overloaded:
If this occurs, release the trigger switch and remove causes of overload, then pull the
switch trigger again to restart.
• When the remaining battery capacity becomes low:
Recharge the battery pack.
Note:
The battery protection system does not in any way damage the tool.
Note:
The indicated capacity may be lower than the actual level during use or immediately
after using the tool.
Spare Part
Part No.
Blades (pack of 20)
PXCLTA-020
Blades (pack of 50)
PXCLTA-050