DESCRIPTION OF SYMBOLS
TROUBLESHOOTING
Removing and Fitting the Blade
Cleaning, Maintenance and Storage
1. To remove the blade bolt, hold the blade firmly
and with a 13mm socket loosen the blade bolt
by turning it anti-clockwise.
NOTE:
A piece of timber will assist in holding
the blade while removing or tightening the blade
bolt.
2. Remove the blade bolt and blade.
3. To fit the blade, place the blade over the centre
hole aligning the different shaped lugs.
NOTE:
The shape of the lugs prevent the blade
from fitting in the wrong direction.
4. Then retighten the fastening bolt with the
universal wrench. The tightening torque should
be approx. 25 Nm.
• Keep all nuts, bolts and screws tight to be sure the lawn mower is in a safe working condition.
• Check the catcher frequently for wear or deterioration.
• Replace worn or damaged parts for safety.
• Only use the replacement blade and blade bolt specified for this product.
• Be careful during adjustments of the lawn mower to prevent entrapment of the fingers between
moving blade and fixed parts of the machine.
• When not in use, the mower should be stored in a dry, frost-free location, out of reach of children.
If the housing of the mower requires cleaning, do not use solvents but a moist soft cloth and brush
only.
• For best results, clean the lawn mower with a brush or rag.
Note: Ozito Industries will not be responsible for any damage or injuries caused by the repair of the
lawn mower by an unauthorised person or by mishandling of the lawn mower. This tool is designed for
DIY use - use in commercial or industrial environments will void the warranty.
WARNING!
ALWAYS ENSURE THE LAWN MOWER
BLADE HAS COMPLETELY STOPPED, REMOVE
SAFETY KEY, BATTERIES AND GRASS CATCHER
PRIOR TO ANY MAINTENANCE.
WARNING!
ALWAYS USE GLOVES WHEN HANDLING
THE BLADE. SHARP EDGES COULD CAUSE INJURY.
Problem Possible Cause
Remedy
Mower is not
starting.
Possible clogging.
Check underneath the mower and clear out
as necessary.
Battery is low in charge.
Charge battery.
Battery not inserted
properly.
Insert battery pack correctly.
Grass too long.
Raise the cutting height to reduce starting
load.
Safety key not inserted
correctly.
Fit correctly.
The drive
motor does
not start.
Mower standing in long
grass.
Start motor on shorter grass or already
mowed area; change cutting height if
necessary.
Mower cutting deck is
clogged.
Clean cutting deck housing so that the blade
can run freely..
Mower is
hard to push.
Height of cut too low.
Raise cutting height.
Cutting blade blunt.
Replace blade.
Possible clogging.
Check underneath the mower and clear out
as necessary.
Grass too long.
Raise the cutting height and walk slower.
Grass too dense.
Raise the cutting height and walk slower and
cut more frequently.
Wet grass.
Wait until the grass dries before mowing.
Motor stops
while cutting.
Height of cut too low.
Raise the cutting height.
Battery has no power.
Charge batteries.
Mower is
not catching
grass
properly.
Height of cut too low.
Raise the cutting height.
Wet grass.
Wait until the grass dries before mowing.
Mower
vibrating.
Bent or damaged blade.
Replace blade.
Unclean cuts. Blade worn.
Replace or sharpen blade.
Wrong cutting height.
Adjust the cutting height.
Replace the metal blade after 50 hours mowing or 2 years
whichever is sooner. If the blade is cracked or damaged
replace it with a new one.
MAINTENANCE
Only replace the blade with a genuine Ozito replacement blade, as this will ensure top
performance and safety under all conditions.
Battery protection system
The tool is equipped with the battery protection system, which helps to ensure a long
service life.
The output power automatically cuts off during operation when the tool and/or battery are
placed under the following situations:
• When the tool is overloaded:
If this occurs, release the start/stop lever safety key and batteries and remove causes
of overload, then reinsert the safety key and batteries, then press and hold the lock-
off button and pull the start stop lever again to restart.
• When the remaining battery capacity becomes low:
Recharge the battery pack.
Note:
The indicated capacity may be lower than the actual level during use or
immediately after using the tool.
• Remove build up of grass in the grass chute.
• Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
• Do not clean the lawn mower with running water,
particularly with high-pressure water.
Read instruction manual.
Nm
Newton Meters
Always keep the lawnmower on the ground when mowing.
Tilting or lifting the lawnmower may cause stones to be thrown out.
Beware of servering toes or hands. Do not put hands or feet near
a rotating blade.
Do not mow in the rain or leave the lawnmower outdoors while raining.
Keep bystanders away. Do not mow whilst people especially children
or pets are in the mowing area.
Blade continues to rotate after the machine is switched off. Wait until all
machine components have completely stopped before touching them.
Pull out Safety Key before
carry out any repair work.
Regulator compliance mark
96
Sound power level
The equipment`s operating time depends on the battery with
the lower charge level. Therefore, only use rechargeable
batteries which are charged to the same level.
IPX1
Ingress protection from water
