background image

3.   When the float switch is 

about 30° higher than 

horizontal (start up level) or 

above the handle, the pump 

will turn ‘on’ and operate 

(water depth of 500mm)

4.   When the float switch is 30° 

lower than the horizontal or 

below the handle, the pump 

will turn ‘off’. (water depth of 

approximately 150mm)

2.   To set the pump to switch off 

at a higher water level, insert 

the float switch cable into 

the adjuster

 

 NOTE:

 There must be a 

minimum of 100mm of cable 

from the adjuster to the float. 

1   When the float switch cable 

is able to move freely the 

pump will function down to 

a water depth of 50mm and 

automatically shut off

2.  L-SHAPE CONNECTOR

3.  FLOAT SWITCH

3.   Screw the prepared 

universal adaptor clockwise 

onto the L-shape connector. 

NOTE. 

The hose/tube/

tap adaptor should not be 

connected at this stage.

4.   Securely attach the hose/

tube/tap adaptor to the 

universal adaptor, fit hose 

clamps if you are using 

flexible hose or tube, and 

tighten well.

2.   Make sure the L-shape 

connector is firmly 

tightened so that the 

O-ring is compressed 

between the pump 

housing and the 

L-shape connector.  

This ensures no leakage 

will occur at this point.

OPERATION

 The pump is fitted with a float switch, which controls how 

the pump switches on and switches off. 

1.   Screw the L-shape 

connector into the pump 

housing by rotating in a 

clockwise direction.

PUSH

100mm

minimum

30°

30°

Summary of Contents for PSDW-350









Reviews: