background image

2.  BATTERY & CHARGING

Charging your lithium ion battery

The tools battery has been shipped in a low charge condition, and requires charging 
prior to use. Allow several cycles of charging and discharging (through use of the tool) 
for the battery to reach its optimum performance / runtime.

CAUTION:

 

THE CHARGER FOR THIS PRODUCT 

SHOULD BE PROTECTED BY A RESIDUAL CURRENT 
DEvICE (RATED AT 30MA OR LESS).

1.    Connect the charger into a mains power outlet.

4.    The charger LED will illuminate 

red signifying that the battery is 

charging.

3.   With the charger sitting on a flat 

surface, align the raised ribs on 

the battery with the recess in the 

charger and slide onto the charger 

ensuring a firm connection.

2.   The charger LED will flash green 

showing power is being supplied 

to the charger.

5.    The charger LED will illuminate 

green once the battery is fully 

charged.

Battery Charge Indicator

The purchased battery is equipped with a 
battery charge indicator to show the state of 
the battery charge.
Press the charge indicator button and look to 
see which LED lights.

Battery requires immediate charging

Low state of charge, requires charging soon.

Mid state of charge

Full state of charge.

Note:

 The battery needs to be removed from the tool to check the state of charge. 

Battery protection system

The tool is equipped with the battery protection system, which helps to ensure a long 
service life.
The output power automatically cuts off during operation when the tool and/or battery 
are placed under the following situations: 

•  When the tool is overloaded:    

   If this occurs, release the trigger switch and remove causes of overload, then pull 

the switch trigger again to restart. 

•  When the remaining battery capacity becomes low: 

  Recharge the battery pack.

Note:

  The battery protection system does not in any way damage the tool.

Note:

 

 The indicated capacity may be lower than the actual level during use or 
immediately after using the tool.

Note:

 

 Always use 2 batteries of same capacity and same charge state with the 
mower.

Charger LED Indicator 

LED Indicator 

Situation

GREEN (Flashing) 

Stand By (no battery pack is inserted) 

RED (Flashing)

Battery is charging (low charge)

RED (Illuminated)

Battery is charging (mid charge)

GREEN (Illuminated)

Battery is fully charged

BOTH(Illuminated)

Battery pack is too hot or too cold (charging will begin 
automatically when battery reaches correct charging 
temperature).

BOTH (Flashing)

Defective battery. Never charge a defective battery 
pack!
Remove battery pack from charger.

Charging your lithium ion battery - Fast Charger

Summary of Contents for Power X Change PXCLMK-418









Reviews: