background image

CARING FOR THE ENVIRONMENT

Tools that are no longer usable should not be disposed of with 

household waste but in an environmentally friendly way. Please 

recycle where facilities exist. Check with your local council 

authority for recycling advice.

Recycling packaging reduces the need for landfill and raw 

materials. Reuse of recycled material decreases pollution in the 

environment. Please recycle packaging where facilities exist. 

Check with your local council authority for recycling advice.

Spare parts can be ordered from the Special Orders Desk 
at your local Bunnings Warehouse.

For further information, or any parts not listed here, visit 
www.ozito.com.au or contact Ozito customer service 
Australia 1800 069 486 
New Zealand 0508 069 486 
E-mail: [email protected]

SPARE PARTS

DESCRIPTION OF SYMBOLS

TROUBLESHOOTING

FAULT

POSSIBLE CAUSES

TROUBLESHOOTING

The 

machine 

will not 

slow down

The throttle lever is set to 

maintain a high speed.

Rotate the throttle lever to a 

lower setting.

The 

machine 

does not 

start.

Correct starting procedure not 

followed.

Follow the instructions  

for starting.

Dirty or old fuel mix.

Replace with clean fuel mix.

Dirty spark plug.

Clean the spark plug and 

adjust the electrode gap or 

fit a new spark plug.

Incorrect carburettor setting.

Contact an authorized 

customer service outlet.

The 

machine 

starts but 

does not 

develop its 

full output.

Incorrect choke lever setting.

Set the choke to the open 

position.

Dirty or clogged air filter.

Clean the air filter.

Incorrect carburettor setting.

Contact an authorized 

customer service outlet.

The engine 

does 

not run 

smoothly

Incorrect electrode gap on the 

spark plug.

Clean the spark plug and 

adjust the electrode gap or 

fit a new spark plug.

Incorrect carburettor setting.

Contact an authorized 

customer service outlet.

Engine 

smokes 

excessively

Incorrect fuel mix.

Use 40 parts fuel to  

1 part oil mix.

Incorrect carburettor setting

Contact an authorized 

customer service outlet.

  

cc

      

Cubic Centimeters (the standard measure of displacement in Europe and Asia) 

 n

o       

No load speed

 /min

      

Revolutions or reciprocation per minute

 dB

      

Decibel level

 

     

 

Read the manual prior to use

 

Regulator compliance mark

 

Wear eye protection

 

Warning

 

 

Pull recoil starter to start motor

Wear ear protection

Fuel inlet

Choke on

Choke off

 

Regulator compliance mark

40:1 Fuel Oil mix ratio

Keep bystanders away

Extremely hot surface.

110

Sound pressure level

Do not smoke

Do not put hands or feet near nozzle when it is running.

 

 

Do not use in the rain or leave the blower outdoors while raining.

Be aware of people around you and do not direct towards them.

Wear safety boots

Wear safety gloves

Thrown objects can cause 

severe injury.

Summary of Contents for PBL-030










Reviews: