background image

5

GENERAL (cont.)

CHARGER AND BATTERY PACK SAFETY INSTRUCTIONS

18. Store idle tools.

When not in use, tools should be stored in a dry, locked up or

high place, out of reach of children.

19. Maintain tools with care.

Keep cutting tools sharp and clean for better and

safer performance. Follow the instructions for maintenance and changing
accessories. Keep handles and switches dry, clean and free from oil and grease.

20. Have your tool repaired by an electrician or power tool repairer. 

This

power tool complies with relevant safety requirements. To avoid danger,
electrical appliances must only be repaired by qualified technicians using
original spare parts; otherwise this may result in considerable danger to the user.

21. Users.

This appliance is not intended for use by young children or infirmed

persons without supervision. Young children should be supervised to ensure that
they do not play with this appliance.

22. Replacement of the supply cord.

If the supply cord is damaged, it must be

replaced by an electrician or a power tool repairer in order to avoid a hazard.

THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING
INSTRUCTIONS FOR YOUR BATTERY CHARGER.

Before using the charger, read all instructions and cautionary markings on
charger, battery pack and product using the battery pack.

Danger!

If the battery pack case is cracked or damaged, do not insert into

charger. There is a danger of electric shock or electrocution.

Warning!

Don’t allow any liquid to get inside charger. Electric shock may result. 

To facilitate cooling of the battery pack after use, avoid placing the charger 
or battery pack in a warm environment such as in a metal shed, or an
uninsulated trailer.

This charger is not intended for any uses other than charging rechargeable
batteries. Any other use may result in risk of fire, electric shock or electrocution.

Do not place any object on top of the charger or place the charger on a soft
surface that may result in excessive internal heat. Place the charger in a
position away from any heat source.

To reduce risk of damage to the electric plug and cord, pull by the plug rather
than the cord when disconnecting the charger.

Make sure cord is located so that it will not be stepped on, tripped over, or
otherwise subjected to damage or stress.

An extension cord should not be used unless absolutely necessary. 
Use of an improper extension cord could result in the risk of fire, electric 
shock or electrocution.

 

Summary of Contents for OZCD144V2BK













Reviews: