background image

ACCESSORY GUIDE

DESCRIPTION OF SYMBOLS

CARING FOR THE ENVIRONMENT

Spare parts can be ordered from the Special Orders Desk 

at your local Bunnings Warehouse. 
For further information, or any parts not listed here, visit 
www.ozito.com.au or contact Ozito Customer Service: 
Australia 1800 069 486 
New Zealand 0508 069 486 
E-mail: [email protected]

SPARE PARTS

Warning 

Read instruction manual

Wear eye and ear protection

/min     Revolutions or 

  

  reciprocation per minute

n

0

  

   No load speed

  V 

    Volts 

   

           Hz 

    Hertz

  ~ 

    Alternating current 

            W 

    Watts

Diameter

Regulator compliance mark

mm

Millimetres

Ah

Amp hour

Wear gloves

Diamond Bits

Ø4.0mm x 1

Ø4.8mm x 1

Ø5.5mm x 1

Diamond

Sharpening Bits

Suitable for sharpening chainsaw chains.

Available in a variety of sizes to suit

different chainsaw blades.

TYPE

QTY / SIZES INCLUDED

APPLICATIONS

Wrench

x 1

Used to fasten accessories to the spindle.

Power tools that are no longer usable should not be disposed of with household waste 

but in an environmentally friendly way. Please recycle where facilities exist. Check 

with your local council authority for recycling advice.

Recycling packaging reduces the need for landfill and raw materials. Reuse of recycled 

material decreases pollution in the environment. Please recycle packaging where 

facilities exist. Check with your local council authority for recycling advice.

Summary of Contents for OMCS-012







Reviews: