REVERSE
CORRECT
BOOST
REVERSE
CORRECT
BOOST
REVERSE
CORRECT
BOOST
REVERSE
CORRECT
BOOST
REVERSE
CORRECT
BOOST
REVERSE
CORRECT
BOOST
REVERSE
CORRECT
BOOST
REVERSE
CORRECT
BOOST
REVERSE
CORRECT
BOOST
REVERSE
CORRECT
BOOST
REVERSE
CORRECT
BOOST
REVERSE
CORRECT
BOOST
REVERSE
CORRECT
BOOST
REVERSE
CORRECT
BOOST
REVERSE
CORRECT
BOOST
REVERSE
CORRECT
BOOST
4. Ensure the Jump Start Power Bank is tucked away securely
in the engine bay and will not be able to fall as a result of
vibrations during the jump start operation. The unit must not be
allowed to come within the range of moving parts.
5. Refer to the status LED’s on the Jump Start Cable.
•
CORRECT Status LED Illuminates Green
All the existing connections are
OK and the vehicle can be started
withing 30 seconds.
•
CORRECT Status LED Flashes Green
All the existing connections are
OK, but the car battery charging
status is very low. Press the BOOST
Button and wait until the green LED
comes on permanently. Start the
vehicle within 30 seconds.
•
CORRECT Status LED Flashes Green and Red Alternately
The jump start function is deactivated after 4 or more attempts
within 10 minutes to protect the device and automatically activates
after 10 minutes.
•
REVERSE Status LED Illuminates Red
A acoustic warning sounds. The
clamps of the jump start cable
are wrongly connected to the car
battery, i.e. with reverse polarity.
Remove the clamps and connect
them to the car battery again but
with the correct polarity and in
accordance with the previous instructions.
•
No Status LED Illuminated, a Acoustic Warning Sounds
Check all the connections,
especially that the clamps are
connected to the car battery
with the correct polarity. If all the
connections are OK, the cause is
probably a defective car battery.
Press the BOOST Button and wait
until the CORRECT Status LED illuminates green. Start the vehicle
within 30 seconds. Replace the defective car battery as soon as
possible.
OPERATION (cont.)
Regulatory Compliance Mark
(RCM)
Warning
V
Volts
A
Amperes
Read Instruction Manual
CCA
A
Cold Cranking Amps
CARING FOR THE ENVIRONMENT
Power tools that are no longer usable should not be disposed
of with household waste but in an environmentally friendly
way. Please recycle where facilities exist. Check with your local
council authority for recycling advice.
Recycling packaging reduces the need for landfill and raw
materials. Reuse of recycled material decreases pollution in the
environment. Please recycle packaging where facilities exist.
Check with your local council authority for recycling advice.
SPARE PARTS
Spare parts can be ordered from the Special Orders Desk at your
local Bunnings Warehouse.
For further information, visit www.ozito.com.au or contact Ozito
Customer Service: Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
DESCRIPTION OF SYMBOLS
3. JUMP START (cont.)
MAINTENANCE
Cleaning
•If the enclosure of the unit requires cleaning, do not use solvents. Use a
moist, soft cloth only. Never immerse any part of the Jump starter power
bank into liquid.
• Keep terminal clamps clean and dry at all times.
Storage
Store the equipment and its accessories in a dark and dry place at
above freezing temperature. The ideal storage temperature is between
+5 and 40°C. Observe the enclosed safety information with detailed
information about storage. Since the battery reacts if the temperature
is too high (above +40°C) or too low (below 0°C), do not keep the
battery permanently in a vehicle. For transporting in a vehicle, place the
equipment in a suitable location where it cannot move in response to an
abrupt change in speed and/or direction. Keep the equipment in its original
packaging.
Note:
At very low temperatures a number of jump start attempts
may be required before the car starts up. Allow one minute waiting
time between each attempt.
Note:
The number of times that you can attempt to start the
engine (max. 10) varies according to the ambient temperature, the
condition of the battery you want to start and the charge level of
the jump starter power bank battery.
6. As soon as the engine is running, remove the Jump Start Cable
from the unit and then remove the Red Positive Terminal Clamp
(+) from the car battery first, followed by the Black Negative
Terminal Clamp (–).
7. Let the engine run. The alternator will charge the vehicle
battery.
