WARNING!
Hold power tool by insulated gripping surfaces when performing an
operation where the cutting accessory may contact hidden wiring or its own
cord.
Cutting accessory contacting a “live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
•
Remove all nails in the work piece before the jigsaw. Cutting nails may damage your
tool.
•
Do not cut hollow pipe with the jigsaw
•
Do not cut material thicker or of a wider diameter than the specified limits.
•
Always allow enough clearance underneath the work piece to ensure the blade does not
touch the floor or work bench, etc.
•
Hold the tool at a comfortable distance from your body. Do not over reach to access the
work piece.
•
Do not touch moving parts with your fingers or hand.
•
Do not cut through walls or cavities without first checking for hidden electrical wires.
•
Ensure that you have tightened the blade prior to starting the machine.
•
When you have finished the cut, wait until the saw blade has stopped moving prior to
removing it from the work piece.
•
Do not touch the saw blade immediately after use. Allow time for the blade to cool, as it
may burn you due to the heat generated during sawing.
•
Always check accessories to ensure that they are suitable for the operating speeds of
this tool.
•
Incorrect accessories can break apart at high speed and cause serious damage or
injury.
•
This appliance is not intended for use by persons
(including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
•
Wear a safety helmet, safety glasses and/or face shield.
It is also highly
recommended that you wear a dust mask, ear protection and padded gloves.
•
Check the blade carefully for cracks or damage prior to operation.
Replace cracked
or damaged blades immediately.
•
Hold the tool firmly during operation. Always hold the adjustable pivoting shoe
firmly against the work piece.
•
Ensure no one is below you when using the tool in elevated conditions.
•
Do not point the tool at anyone in the immediate vicinity.
WARNING!
When making a “blind” cut (you can’t see behind what is being cut),
be sure that hidden electrical wiring or water pipes are not in the path of the cut.
If wires are present, they must be disconnected at their power source by a qualified person or
avoided to prevent the possibility of lethal shock or fire.
•
Water pipes in “blind” areas must be drained and capped before cutting.
•
If the blade hits against objects during operation, damage to the tool or dangerous blade
breakage may occur.
•
Watch out for cut-off portions
of the work piece being cut. They may fall and cause
injury to you or someone near you.
•
When cutting metals, be cautious of hot flying debris.
•
Do not touch the blade or the work piece immediately after operation;
they may be
extremely hot and could potentially burn your skin.
•
If you withdraw the blade from the work piece during operation, a strong reaction
could be produced,
which could cause the blade to snap or cause you to lose your grip
and/or control of the saw. Always switch off the tool and wiat until the blade has come to
a complete stop before with drawing the blade from the work piece.
WARNING!
Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contain chemicals known to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement and other masonry products
• Arsenic and chromium from chemically treated timber
Your risk from exposure to these chemicals varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated area and work
with approved safety equipment, such as dust masks that are specially designed to filter out
microscopic particles.
WARNING!
When using mains-powered tools, basic safety precautions, including the
following, should always be followed to reduce risk of fire, electric shock, personal injury
and material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before
operating the tool.
Save these instructions and other documents supplied with this tool for future reference.
The electric motor has been designed for 230V and 240V only. Always check that the power supply
corresponds to the voltage on the rating plate.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand.
This tool is double insulated in accordance with AS/NZS 60335-1;
therefore no earth wire is required.
If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid
a hazard.
Note:
Double insulation does not take the place of normal safety precautions when operating this tool. The
insulation system is for added protection against injury resulting from a possible electrical insulation failure
within the tool.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the
extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective.
When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not
suitable for the power input of the tool or which is damaged or defective may result in a risk of fire and electric
shock.
WARNING!
Read all safety warnings and all instructions.
Failure to follow the warnings
and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and
instructions for future reference. The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a.
Keep work area clean and well lit
. Cluttered or dark areas invite accidents.
b.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
c.
Keep children and bystanders away while operating a power tool.
Distractions can cause you to
lose control.
2. Electrical safety
a.
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will
reduce risk of electric shock.
b.
Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your body is earthed or grounded.
c.
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the
risk of electric shock.
d.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords
increase the risk of electric shock.
e.
When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a
cord suitable for outdoor use reduces the risk of electric shock.
f.
If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply.
Use of an RCD reduces the risk of electric shock.
3. Personal safety
a.
Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in serious personal injury.
b.
Use personal protective equipment. Always wear eye protection.
Protective equipment such as
dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will
reduce personal injuries.
c.
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to
power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your
finger on the switch or energising power tools that have the switch on invites accidents.
d.
Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
e.
Do not overreach. Keep proper footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
f.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.
g.
If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related hazards.
4. Power tool use and care
a.
Do not force the power tool. Use the correct power tool for your application.
The correct power
tool will do the job better and safer at the rate for which it was designed.
b.
Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c.
Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools.
Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with
the power tool or these instructions to operate the power tool.
Power tools are dangerous in the
hands of untrained users.
e.
Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts
and any other condition that may affect the power tool’s operation. If damaged, have the power
tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f.
Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g.
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed.
Use of the power tool for
operations different from those intended could result in a hazardous situation.
5. Battery tool use and care
a.
Recharge only with the charger specified by the manufacturer.
A charger that is suitable for one
type of battery pack may create a risk of fire when used with another batery pack.
b.
Use power tools only with specifically designated battery packs.
Use of any other battery packs
may create a risk of injury and fire.
c.
When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects, that can make a connection from one terminal
to another.
Shorting the battery terminals together may cause burns or a fire.
d.
Under abusive conditions, liquid may be ejected from the battery; aviod contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritationor burns.
6. Service
a.
Have your power tool serviced by a qualified repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is maintained.
b.
If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or
similarly qualified persons in order to avoid a hazard.
GENERAL POWER TOOL SAFETY WARNINGS
ELECTRICAL SAFETY
COMBI SAW SAFETY WARNINGS
