Chain sharpening
Sharpen the chain regularly to maintain optimum performance
of the pole pruner.
Signs of a dull chain are:
• The sawdust becomes
powder-like
• Extra force is required to
execute a cut
• The cut does not track
in a straight line
• Increased vibration
Sharpen each cutter using a chain
file. Always use outward strokes
and maintain a 30° angle between
the chain and file. After sharpening, the cutters must all have the
same width and length.
Guide bar wear
Reverse the guide bar every 8 working hours to ensure uniform wear.
Check the guide rails frequently and if necessary remove burrs and
square up the rails using a flat file.
Power cord replacement
If the replacement of the supply cord is necessary, this has to be done
by the manufacturer or his agent in order to avoid a safety hazard.
Cleaning and storage
• Regularly clean the tensioning mechanism by blowing compressed
air onto or cleaning it with a brush. Do not use any tools for the
cleaning.
• Keep oil away from the handle in order to ensure a secure hold.
• Clean the machine as necessary with a damp cloth and a mild
cleanser, if appropriate.
• If the pole pruner is not used for an extended period of time,
remove the chain and bar oil from the tank. Briefly place the chain
and the guide bar in an oil bath and then wrap it in oil paper.
• Always replace the protective cover for transport or storage of the
pole pruner.
• Pull out the electrical plug before cleaning.
• Never immerse the machine in water or other liquids.
• Store the pole pruner in a safe and dry place and out of the
reach of children.
Note:
The pole pruner warranty does not cover components that have
been subjected to operator abuse or negligence. To receive full value
from the warranty, the operator must maintain the pole pruner as
instructed in this manual.
Ozito Industries will not be responsible for any damage or
injuries caused by repair of the tool by an unauthorised person
or mishandling or mistreatment of the tool. This tool is designed
for Domestic Home Use only. Use in commercial or industrial
environments will void the warranty.
CARING FOR THE ENVIRONMENT
Tools that are no longer usable should not be disposed of with
household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council
authority for recycling advice.
Recycling packaging reduces the need for landfill and raw
materials. Reuse of recycled material decreases pollution in the
environment. Please recycle packaging where facilities exist.
Check with your local council authority for recycling advice.
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito customer service
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
DESCRIPTION OF SYMBOLS
Read instructions
V
Volts
Hz
Hertz
~
Alternating current
W
Watts
Revolutions per minute
Double insulated
n
o
No load speed
Warning
Use eye, ear and head protection when operating the pruner
Disconnect and discontinue use should the power cord be damaged
Maintain a minimum clearance of 10 m from current-carrying lines.
Life-threatening danger from electric shock.
min-¹
Keep bystanders away
105
Sound pressure level
Do not expose to rain or leave
outdoors while raining
Regulator compliance mark
Wear safety gloves
Wear sturdy, non-slip
footwear
Watch out for falling and
catapulting parts
10 m
MAINTENANCE
LEFT HAND
CUTTERS
RIGHT HAND
CUTTERS
30°
30°
2
9.53mm
(3/8)
1.3mm(
.050”)
33 Links
WARNING!:
WEAR HEAVY GLOVES WHEN
HANDLING THE CHAIN. HOLD THE GUIDE BAR
SECURELY IN A VICE.
IMPORTANT!
BEFORE CLEANING YOUR POLE PRUNER
OR CARRYING OUT ANY MAINTENANCE PROCEDURE,
MAKE SURE THAT THE MOTOR IS OFF AND THE TOOL
DISCONNECTED FROM THE POWER SUPPLY
TO PREVENT ACCIDENTAL STARTING.
Chain Replacement:
The chain can be purchased through Ozito spare parts or from your
local Bunnings Warehouse. The correct chain can be purchased by
matching the pitch, gauge and number of links as shown below:
LEFT HAND
CUTTERS
RIGHT HAND
CUTTERS
30°
30°
2
9.53mm
(3/8)
1.3mm(
.050”)
33 Links