Ozito Industries will not be responsible for any damage or injuries
caused by repair of the tool by an unauthorised person or mishandling
or mistreatment of the tool. This tool is designed for Domestic Home Use
only. Use in commercial or industrial environments will void the warranty.
CAUTION!:
ALWAYS HANDLE THE BLADE WITH CARE
– SHARP EDGES COULD CAUSE SERIOUS INJURY.
USE GLOVES.
MAINTENANCE
WARNING!:
BEFORE CLEANING YOUR ECOMOW
ELECTRIC MOWER OR CARRYING OUT ANY
MAINTENANCE PROCEDURE, MAKE SURE THAT THE
MOTOR IS OFF AND THE TOOL DISCONNECTED FROM
THE POWER SUPPLY TO PREVENT ACCIDENTAL
STARTING.
Removing the Blade
1. To remove the blade bolt, hold the
blade firmly and with a 13mm socket
(not supplied) loosen the blade bolt
by turning it anti-clockwise.
Note:
A piece of timber will assist in
holding the blade while removing or
tightening the blade bolt.
2. Remove the blade bolt and blade.
3. Inspect for damage and clean as
necessary.
Replace the metal blade after 50 hours mowing or 2 years whichever is
the sooner – regardless of condition. If the blade is cracked or damaged
replace it with a new one. Never use a blade bolt if the insulated head is
damaged, cracked or missing.
TIMBER
Fitting the Blade
• Keep all nuts, bolts and screws tight to be sure the lawn mower is in a safe
working condition.
• Check the catcher frequently for wear or deterioration.
• Replace worn or damaged parts for safety.
•
Only use the replacement blade, blade bolt, and impeller specified for this
product.
• Be careful during adjustments of the lawn mower to prevent entrapment of
the fingers between moving blade and fixed parts of the machine.
• Oil the wheel pins.
• When not in use, the mower should be stored in a dry, frost-free location, out
of reach of children.If the housing of the mower requires cleaning, do not use
solvents but a moist soft cloth and brush only.
•
Frequently check the wheel threads are firm and tight.
CAUTION!:
DO NOT TOUCH ROTATING BLADES.
1. Fit the blade to the fan with the tilt edges of the blade facing towards the
mower, ensuring the blade is located onto the fan location lugs correctly.
2. Re-assemble blade bolt through blade and fan.
3.
Hold the blade firmly and tighten blade bolt with a (not supplied), by turning
in a clockwise direction. The tightening torque should be approx. 25 Nm.
SERVICE INFORMATION
Please note that the following parts of this product are subject to normal
or natural wear and that the following parts are therefore also required
for use as consumables.
* Not necessarily included in the scope of delivery!
Category
Example
Wear parts*
Carbon brushes, V-belt
Consumables*
Blade
Missing parts
Only replace the blade with a genuine Ozito replacement blade, as this will
ensure top performance and safety under all conditions.
TROUBLESHOOTING
Problem
Cause
Remedy
The motor
fails to start
The capacitor is
defective
The mower housing is clogged.
Have repaired by the Customer
Service Centre
There is no electricity
at the plug
Check the cable and the fuse
The cable is defective
Check the cable
The combined switch/
plug is defective
Have repaired by the Customer
Service Centre
The connectors have
become separated
from the motor or the
capacitor
Have repaired by the Customer
Service Centre
The mower is standing
in high grass
Start in low grass or on an area
that has already been mowed;
change the cutting height if
necessary
Start in low grass or
on an area that has
already been mowed;
change the cutting
height if necessary
Clean the housing so that the
blade moves freely
The motor
performance
drops
The grass is too high
or too damp
Correct the cutting height
The mower housing is
clogged
Clean the housing
The blade is severely
worn
Replace the blade
Cutting is
irregular
The blade is worn
Replace or re-sharpen the blade
Wrong cutting height
Correct the cutting height
