Pump Control Unit
‘GREEN Power on’.
This indicates that there is power to the
pump, but the pump is currently not on.
‘ GREEN Pump on’.
This indicates that there is power to the
pump and the pump is running.
‘RED F GREEN’.
There is power to the pump, but flow is
stalled. In this event, press the Restart
button.
If the malfunction still occours, refer to the
“
TROUBLESHOOTING”
section to find a
remedy.
‘RESTART Button’.
When the pump requires restating (Failure
light illuminates red), push the Restart
button and hold for 5 seconds to re-start
the pump, the red failure light should
turn off. If the failure light re-illuminates
red, refer to the “
TROUBLESHOOTING”
section to find a remedy.
Note:
If all three lights are on; the Pump has detected a failure, but will
continue to run for approx. 10 seconds to attempt to fix the problem.
CPPAS-800
6. OPERATING THE PUMP
7. RECOMMENDED SETUP
WARNING!
THE INPUT HOSE OR PIPE SHOULD BE
LOW ENOUGH IN THE WATER TO ENSURE THAT IF
THE WATER LEVEL FALLS, THE PUMP WILL NOT RUN DRY.
ENSURE THAT THIS IS CHECKED WHEN IN OPERATION.
Positioning the hose or pipe
Position the input hose or pipe so that it rises from the water drawing
source to the pump. Where possible, avoid positioning the input hose
or pipe higher than the pump, as this would delay the escape of air
bubbles from the input hose or pipe and impede the priming process
(see section ‘
Priming the pump
’ for description on priming the pump)
• The suction line should be as short as possible, since the conveying
capacity decreases as the length of the line increases.
Note:
A leaking hose or pipe will draw in air and therefore not draw in
any water.
Note:
A non-return valve is recommended so that the water does not
run off when the pump is shut off.
Note:
A suction in-line filter with a 3000l/hour min flow rate, and 150 to
250 micron mesh must be used to protect the pump from sand, dirt etc.
The Ozito PAPF-001 Pre-filter or equivalent is available from Bunnings
stores.
Note:
During the initial set-up, please purge all air from the system via
the discharge outlet highest in the system.
Recommended set-up
CONNECTION WITH TANK BASE BELOW WATER PUMP
P
CONNECTION WITH TANK BASE ABOVE THE WATER PUMP
CONNECTION WITH TANK BASE LEVEL WITH WATER PUMP
FIRM BASE
SOLID STRUCTURE
WATERTANK
WATERTANK
NON-RETURN
VALVE
DISCHARGE
OUTLET
GATE
VALVE
GATE
VALVE
SUCTION LINE
SUCTION LINE
150mm
150mm
150mm
150mm
150mm
FIRM BASE
SOLID STRUCTURE
DISCHARGE
OUTLET
150mm
UNION
COUPLING
depending on
installation
UNION
COUPLING
depending on
installation
WATERTANK
GATE
VALVE
SUCTION LINE
SOLID STRUCTURE
DISCHARGE
OUTLET
FIRM BASE
UNION
COUPLING
depending on
installation
IN-LINE
FILTER
IN-LINE
FILTER
IN-LINE
FILTER
CONNECTION WITH TANK BASE BELOW WATER PUMP
P
CONNECTION WITH TANK BASE ABOVE THE WATER PUMP
CONNECTION WITH TANK BASE LEVEL WITH WATER PUMP
FIRM BASE
SOLID STRUCTURE
WATERTANK
WATERTANK
NON-RETURN
VALVE
DISCHARGE
OUTLET
GATE
VALVE
GATE
VALVE
SUCTION LINE
SUCTION LINE
150mm
150mm
150mm
150mm
150mm
FIRM BASE
SOLID STRUCTURE
DISCHARGE
OUTLET
150mm
UNION
COUPLING
depending on
installation
UNION
COUPLING
depending on
installation
WATERTANK
GATE
VALVE
SUCTION LINE
SOLID STRUCTURE
DISCHARGE
OUTLET
FIRM BASE
UNION
COUPLING
depending on
installation
IN-LINE
FILTER
IN-LINE
FILTER
IN-LINE
FILTER
WARNING!
TO ENSURE CORRECT PUMP OPERATION
IT IS ESSENTIAL THAT A SUCTION IN-LINE FILTER BE
USED FOR A CLEAN WATER SUPPLY.
INSTALLATION
