background image

3.  ADJUSTING THE SPRAY GUN

OPERATION

2.  PREPARATION

1   Before pouring any paint 

or thinners work out how 

much of each substance is 

needed.

3   Once the correct viscosity 

is obtained, pour the 

mixture into the paint pot.

Thinning is particularly important when spraying. Most paints 

are supplied ready for brush application and need to be diluted 

sufficiently for spraying purposes. 

Follow the manufacturers guide for thinning ratios which 

should be labelled on the paint container.

2   Pour the required paint and 

thinners through a filter into 

a mixing cup and then mix 

thoroughly.

Thinning

NOTE:

 

FOR BEST RESULTS, SURFACE PREPARATION AND PAINT 

THINNING ARE THE TWO MOST IMPORTANT AREAS. ENSURE 

ALL SURFACES ARE FREE OF DUST, DIRT AND GREASE.

IMPORTANT!

 

THE SPRAY GUN CANNOT BE USED WITH 

MATERIALS CONTAINING ABRASIVE SUBSTANCES, GLAZES, 

CAUSTIC AND ALKALINE SUBSTANCES.

Note:

  The further the variable trigger is pressed, the more fluid 

will flow through the gun.

1   Fully tighten the fluid 

adjustment dial.

The fluid adjustment dial is a stop that limits the distance the 

trigger can be pressed and can therefore limit the amount of 

paint being sprayed.

2   Slightly loosen the fluid 

adjustment dial, then test 

setting on a scrap piece of 

material.

Variable Trigger

Fluid Adjustment Dial

PAINT

THINNERS

PAINT

THINNERS

3   Repeat step 2 until desired fluid output is reached.

1   To restrict the air pressure 

entering the spray gun 

turn the valve clockwise.

Air Regulator Valve

1   Squeeze the variable 

trigger to start spraying.

2   Release the variable 

trigger to stop spraying.

The air regulator valve controls the air pressure entering the gun.

2   To increase air pressure 

entering the gun, turn the 

air valve anti-clockwise.

Summary of Contents for ASG-GFK













Reviews: