3. CONTROLS
OPERATION
Mode Selection
Before use, peel off the protective film from the front and
inner lens.
Shade number can be manually set by adjusting the mode selector
from grind, shades 5-9 or 9-13. The specific shades can then be
selected using the shade adjustment dial.
1. Set the mode selector to ‘5-9 (circled)’
or ‘9-13’ depending on the application.
2. Turn the shade adjustment
dial to the desired shade
level (circled numbers are
for mode 5-9 and un-circled
numbers are for mode 9-13.
WARNING!
ALWAYS ENSURE THE CORRECT MODE
AND SHADE IS SELECTED BEFORE WELDING.
Note:
Shade level should be based on the welding process and
arc current being used. Refer to the lens shade level guide on the
inside of the mask for guidance.
Note:
Set the mode to ‘GRIND’ if using the helmet while grinding.
The auto darkening function does not activate in GRIND mode.
WARNING!
DO NOT WELD IN GRIND MODE, THE LENS
WILL NOT DARKEN.
WARNING!
ARC RAYS FROM THE WELDING PROCESS
PRODUCE INTENSE VISIBLE AND INVISIBLE
(ULTRAVIOLET & INFRARED) RAYS THAT CAN BURN
EYES AND SKIN. SPARKS CAN ALSO FLY OFF FROM
THE WELD, CAUSING BURNS.
CR
2450
3V
+
SENSITIVITY
DELAY
LOW
HIGH
MIN
MAX
OZITO ADWH-913V
SHADE: 4 / 5-9 / 9-13
AS/NZS 1337.1 V & 1338.1
MADE IN CHINA
LOW
BATTERY
TEST
WELD (9-13)
GRIND (4)
( 5 - 9 )
12 | 7
8
10
13 | 9
5 | 9
11 | 6
5
350
100
175
400
125
200
450
150
225
500
250 275 300
10 15 20 30 40 60 80
ARC CURRENT (A)
SAW
MIG (LIGHT)
PAC
PAW
MIG (HEAVY)
TIG, GTAW
MAG / CO2
ARC (SMAW)
9
10
9
10
11
12
13
14
10
10
8 9
11
11
12
13
14
11
13
14
14
11
12
12
13
11
14
12
12
13
14
10
10
10
11
12
13
14
11
12
15
15
15
13
14
15
WELDING
PROCESS
SHADE LEVEL GUIDE
*The shade levels listed are only a recommendation for various working applications.
Depending on the conditions of use, the next shade level up can be used.
WARNING!
ENSURE THE LOW BATTERY INDICATOR
LIGHT IS OFF & YOU HAVE VERIFIED THE WELDING
HELMET IS WORKING PROPERLY WITH THE “TEST”
FUNCTION BEFORE PROCEEDING TO WELD.
WARNING!
BEFORE WELDING, ADJUST THE AUTO-
DARKENING LENS SENSITIVITY SETTING TO MEET THE
APPLICATION. ENSURE THE CORRECT SHADE IS USED
FOR THE APPLICATION.
WARNING!
WELDING HELMETS DO NO PROVIDE
UNLIMITED EYE, EAR AND FACE PROTECTION.
WARNING!
NEVER WELD WITH ANY OF THE LENS OR
FILTERS REMOVED.
ADWH-913V
Sensitivity
Adjust this to suit ambient and welding light levels.
Low sensitivity is best for
high current welding, whilst
the high setting is suited for
welding with small currents.
The medium setting is suitable
for the majority of indoor and
outdoor welding activities.
1. To adjust, turn the dial to the lowest setting and face the helmet
in the direction of use, exposing it to the surrounding light
levels.
2. Gradually increase the sensitivity until the lens darkens.
3. Then lower the sensitivity just slightly below the setting in step
2.
Note:
Slight re-adjustment may be necessary for certain
applications or if the lens is flashing on and off.
Delay Time
The delay time controls the
time taken for the helmet to
switch between full dark and
full light. This can be adjusted
between 0.1s to 0.8s.
The short delay time is suitable for spot, seam or short welding
sessions. The medium setting is suitable for the majority of indoor
and outdoor welding. Use the long delay time for high current
welding or to prevent eye fatigue during long welding sessions.
CR
2450
3V
+
SENSITIVITY
DELAY
LOW
HIGH
LOW
HIGH
WELD
GRIND
OZITO ADWH-913V
SHADE: 4 / 9-13
LOW BAT
TEST
CR
2450
3V
+
SENSITIVITY
DELAY
LOW
HIGH
LOW
HIGH
WELD
GRIND
OZITO ADWH-913V
SHADE: 4 / 9-13
LOW BAT
TEST
