background image

The device can also be controlled via the included remote control. The 

remote control has 7 buttons that perform the same function as the 

main control panel. When using the remote control, point it towards to 

the control panel in the middle of the heater. 

MAINTENANCE

This devices features 2 removable air filters. The air filters are designed to capture dust 

and airborne dirt, and should be inspected and cleaned once a month, or as needed 

on a periodic basis. The accumulation of excess dust and dirt in the air filters can nega-

tively affect the performance of this device. Before attempting to clean, always turn 

off the device by switching the master switch off on the back of the device first. Then 

unplug the device’s power cord from the wall outlet.

1.  Ensure  that  the  above  instructions  were  followed  by  turning  off  the  fan  and 

unplugging it from the outlet first.

2.  Wipe the surface and outside of the device by using a damp soft cloth. Do not 

immerse in water and never use thinners or other cleaning solutions as these may 

damage the fan’s surface appearance. 

3.  Remove and clean the filter covers first with a duster and then wipe away any 

excess dust with a damp soft cloth. Ensure that the filter covers are completely dry 

when finished.

4.  Remove the air filters as shown in the following illustration. Clean the air filters by 

immersing them in clean water for several minutes. Ensure that the air filters are 

allowed to dry completely when finished.

5.  Once  thoroughly  dried,  place  the  cleaned  air  filters  back  into  the  device  and 

assemble securely with the filter covers, as shown in the illustration below.

Unpack the heater and check that you have main heater, the glass base, and remote 

control unit. Place the main heater flat on the ground (laying on its side) and remove 

the locking nut from the bottom end. Connect the glass base onto the bottom, and 

secure together with the locking nut.

Note: Ensure the locking nut is firmly secured before standing the heater up on 

its base. 

REPLACING BATTERY

Your  remote  control  is  powered  by  an  included 

CR2032  Lithium  battery. To  replace  the  battery, 

pull out the battery holder and insert a new 

battery. Ensure that the polarity is correct and 

then insert the battery holder back into the 

remote control (Fig 3).

When the heater’s power is on, the remote 

control can be used to operate the heater from up 

to 20 feet away. Note: if there are two or more 

heaters within this distance, both will be 

operated by the same remote control. If the 

remote control will not be used for a long 

period of time, remove the batteries from the 

battery compartment.

OPERATING THE HEATER

This heater and fan can be operated via the built-in touch control panel, and via the 

remote control device. Before using this device, read through and follow all safety 

warnings printed in this manual. 

Control Panel Overview:

To use the built-in control panel, first press the master power switch located behind 

the fan towards the bottom (see point 9 on page 5). A deep sound will confirm that 

the master switch has been engaged. Then press the power button located at the top 

of the device (see point 3 on page 5). The following touch control buttons will illumi-

nate on the control panel:

The following indicator icons will illuminate immediately above the control panel’s 

touch buttons. The indicators icons will activate based on the settings you choose via 

the touch buttons. 

Using  the  control  panel’s  buttons,  press  Heater  (1)  to  turn  on  the  top  heater,  and 

Heater (2) to turn on the bottom heater.

Continue to press each to cycle through each heater’s off, low and high settings. The 

following icons will appear:

 

Indicates the heater will release air at the low speed setting.

 

Indicates the heater will release air at the high speed setting.

To activate the heater’s thermostat, press the Temp/Timer icon:

The  room  temperature  display  will  flash  on  the  screen.  Press  the                        press                            

buttons to set the thermostat to your desired heating temperature. The heater will 

remain until it detects the room temperature equals the thermostat temperature. 

To activate the fan without the heating element, press the minus to the lowest 

possible setting of 59°F, and then press the minus button one more time. The 

screen will show the following icon to confirm that it is in fan mode. 

For maximum fan performance, ensure the Heater (1) and (2) are set to their high 

speed settings.

To activate the fan’s timer, press the press the Temp/Timer icon again: 

In  timer  mode,  instead  of  displaying  the  temperature,  0  H  will  flash  on  the  LCD, 

indicating zero hours. Press the press                      buttons to increase or decrease the 

timer in units of 1 hour, up to a maximum of 12 hours. The timer will stop flashing to 

indicate it is programmed, and keep the heater on until the number of hours chosen 

has passed. Note, changing the timer once it has started will reset it. 

To engage the heater and fan’s oscillation, press the SWING button on the far 

right side of the control panel. The following icon will appear to confirm that 

the device is in oscillation mode.

8

Summary of Contents for OZH1











Reviews: