ASSEMBLY INSTRUCTIONS
NOTE :
To prolong the life of the tent floor, select a level, clean area for the
campsite. To prevent damage to the zipper, unzip the door to allow air to enter
the tent. To improve the weather resistance of your tent, it is advisable to use
seam sealer to coat all exposed seams. You should apply only to the underside
of the fly and inside seams of the tent. If applied to the outside seams,
discoloration of your tent may occur. Seam sealer is available in the camping
section of any local sporting goods store.
IMPORTANT :
WE ADVISE YOU TO ASSEMBLE THE TENT ONCE BEFORE
GOING CAMPING TO BECOME FAMILIAR WITH THE ASSEMBLY OF THE TENT.
STEP 1 :
Set up your 10’ x 10’ canopy following the directions that came
with the canopy. Make sure it is staked to the ground.
NOTE :
To take down tent, follow steps above in the reverse order. Be sure to leave
door and windows unzipped. Place stakes into stake bag and pole into the pole bag,
which are provided.
Make sure tent is clean and dry before storing.
The tent
should be folded into equal parts toward the center of the tent to distribute the bulk.
Start a small tight roll, the width of the carry bag, with the pole bag placed at the
end opposite the door. Roll tent toward door to allow air to escape. Once rolled, tie
a string or rope around tent to hold into place. Place tent, frame and stakes into carry bag.
MODEL W634.1A
4 PERSON CONNECTENT FOR CANOPY
STEP 2 :
Spread the tent out flat, next to the canopy with the floor side down
and unzip the door. Locate the door so that it faces the center of the Canopy.
STEP 3 :
Locate the two “S” hooks on the elastic cording
that are located in the upper corners of the tent. These connect
to the eyelets in the upper corners of the canopy. Starting at one
corner of the canopy connect the “S” hook.
Tent should appear as shown.
WARNING :
Elastic cords can snap back and hit your eye.
To reduce the risk of injury to you and others:
• Keep your body and face clear.
• Do not over stretch elastic cords.
• Maintain firm grip on hook.
• Pull the hook toward you; if it slips it will spring away from you.
• Make sure hook is fully clipped to canopy before releasing.
• Wear protective eye wear during tent assembly.
Your failure to follow this warning could cause serious injury or
permanent disability.
STEP 4 :
Connect the clips along the side of the canopy, then connect the "S”
hook to the other corner.
STEP 5 :
There is a hook and loop tab at the center of the
tent above the door. Connect this to the canopy frame.
STEP 6 :
There are “S” hooks located at the bottom corners
of the tent. These should be connected to the holes in the
bottom of the canopy legs.
STEP 7 :
Tie the fabric ties located on the tent around the
canopy legs to secure the tent to the canopy frame.
STEP 8 :
Extend the fiberglass tent pole (A) by pulling out each section and
placing the ends into the metal ferrules.
STEP 9 :
Slide the pole through the red sleeve on the roof of the tent.
STEP 10 :
On one side of the tent insert the pin located at the base
of the tent into the ferrule at the end of the fiberglass frame pole.
STEP 11 :
Go to the opposite side of the tent and carefully flex the tent pole and
place the ferrule at the end of the pole onto the metal pin at the base of the tent.
STEP 12 :
Clip the plastic hooks on the tent to the fiberglass pole.
STEP 13 :
Stake down tent by inserting stakes through the stake loops at the
corners of the tent, hammering stakes into ground at a 45° angle, making sure
the tent floor is pulled out even and snug. Continue staking
down the tent with the stakes through the rings where the poles
attach to the pin.
STEP 14 :
Attach the hooks on the fly to the fabric loops located
next to the clips that hold the tent to the fiberglass pole.
STEP 15
: Secure the fly by wrapping the Velcro
fasteners at each corner of the fly around the tent
pole.
STEP 16 :
Guy ropes have been provided for the fly. Extend each of the guy ropes
which are attached to the fly edges. Make a loop at the opposite end of the guy rope,
by using slider as shown and place loop over a tent stake.
Adjust slider to make guy rope tight and stake to the ground.
NOTE :
The fly can be rolled back and held with toggles to allow extra ventilation
at the top of the tent.
NOTE :
There is an adapter kit available that will allow this tent to connect to a
12 x 12 canopy. See the parts list on the opposite side of these instructions for
directions on how to order.
A
A
