OC-1204A User’s Manual - Rev 1.0
SPECIFICATIONS
1
AC Power Input Characteristics
Normal
Withstand
Unit
1-1
Input voltage :
220-240
200~260
Vac
1-2
Input frequency :
50/60
47-63
Hz
1-3
Unload input current :
80
max.
mAac
1-4
Input current consumption at 240Vac input, output 13.5V 4A loading
.55
±10%
Aac
1-5
Nominal efficiency: at 240Vac input, output 13.5V 4A
>80%
2
Charging Output Control Characteristics
2-1
Soft Start
→
Bulk Charge
→
Absorption Charge
→
Float Charge (Full)
2-2-1
Soft Start – start conditions:
3
±0.5
Vdc
2-2-2
Soft Start output current controlled:
2
±0.5
Adc
2-2-3
Soft Start mode transits to Bulk mode when battery voltage is above:
11.0
±0.5
Vdc
2-2-4
Soft Start charging time limited: Stop charging if battery voltage cannot reach 12.0V
4
±0.5
Hours
2-3-1
Bulk charging current controlled:
4
±0.2
Adc
2-3-2
Bulk charging time( Tcc ) limited:
16
±0.5
Hours
2-4-1
Absorption Mode charging output voltage controlled:
14.5
±1%
Vdc
2-4-2
Absorption mode transits to Float mode conditions:
1) Maintains charge until current drops by less than 0.1A over a 1 hour period.
2) Maintains charge for 2 hours until the charging current drops by less than 0.5A.
2-4-3
Absorption maximum charging time(Tcv) limited: (Force to Float mode when
Time-out)
8
±0.5
Hours
2-5-1
Float charging output voltage controlled:
13.7
±1%
Vdc
2-5-2
Maximum Float charging current controlled:
2.0
±0.2
Adc
2-5-3
Float charging time limited:
4
±0.2
Hours
2-5-3
Restarts to Bulk charging when the battery voltage is below:
12.8
±0.5
Vdc
2-6
Unload output voltage when battery is disconnected
0.5
Max.
Vdc
2-7
Output short-circuit current when battery is disconnected :
1
Max.
mAdc
2-8
Battery flow back current (to the charger) when connected to 12V battery, AC Power
disconnected :
1
Max.
mAdc
3
Safety & Protection
3-1
Built in Temperature Protection.
3-1
Output Short Circuit Protection, Reverse Polarity Protection
4
Electrical Parts
4-1
Input Connector
6 feet VDE H03VVH2-F 2X0.75mm
2
with 2PIN SAA plug.
4-2
Out Put Connector
4 feet - Anderson PP30 Type Connector
5
Physical Parameters
5-1
Plastic Enclosure Dimensions
164(L) x 85(W) x 55(H) mm
5-5
Net weight :
approx. 620g
6
Environmental Characteristics
6-1
Operating temperature :
0 to 40
o
C
6-2
Storage temperature :
-25 to 85
o
C
6-3
Operating Humidity range :
0 to 90% RH
6-4
Cooling:
Passive / Natural
2 YEAR MANUFACTURER WARRANTY
Zylux Distribution Pty. Ltd. (OzCharge) warrants to the Customer that this product is substantially free from defects in materials and
workmanship under normal use for a period of 2 Years from the Date of Purchase.
Please ensure you keep a copy of your receipt on file as this will be required for proof of purchase and to validate your warranty.
Obtaining Warranty Service
Within the warranty period, the Customer must contact the authorised supplier / retailer where the product was purchased or
alternatively you can contact the OzCharge service centre through one of the following methods:
Hotline
: (03) 9482 2203
Website
:
www.ozcharge.com.au
If the Authorised Supplier and / or OzCharge service centre concludes that while under normal use, a product failure or malfunction
occurred during the warranty period and was caused by a defect in material or workmanship (see Exclusions), the Customer will be
asked to ship to the nearest service point. The product must be packaged appropriately for safe shipment. To prove that the
product is under warranty, the customer should enclose a copy of their receipt for proof of purchase. It is recommended that
returned products be sent by registered mail as Zylux Distribution Pty Ptd. (OzCharge) accepts no responsibility / liability for goods
lost or damaged in transit. Return Shipping costs to be incurred by the Customer.
Exclusions
If upon receiving a product for repair and if testing and examining the product has disclosed that the alleged defect or malfunction
in the product does not exist or was caused by the Customer or any third persons misuse, physical abuse, water damage,
unauthorised attempts to open, repair or modify the product or improper installation, this will not be covered under this warranty.
This Warranty is void if:
1. The product has been tampered or repaired by unauthorised personnel.
2. The warranty seal is broken or altered.
3. The warranty period has expired.
