EN 13034:2005+A1:2009
Protection against liquid chemical, light spray (type 6)
EN ISO 13982-1:2004+A1:2010
Protection against airborne solid particulates (type 5)
EN 1073-2:2002
Particulate radioactive contamination (no rays)
EN 1149-5:2008
Electrostatic charges
EN 14126:2003+AC:2004
Protection against infectious agents
EN ISO 13688:2013
Protective clothing - general requirements
S
M
L
XL
XXL
XXXL
Body height
164-170
170-176
176-182
182-188
189-194
194-200
Chest
circumference
84-92
92-100
100-108
108-116
116-124
124-132
PURPOSE:
OxyChem C 210 one-piece coverall is a protective clothing with limited life, Type 6 protection
(according to EN 13034: 2005 + A1: 2009) and Type 5 (according to ISO 13982-1: 2004 + A1: 2010),
intended for protection in in case of potential exposure to light spray, liquid aerosols or low-pressure and
not too abundant spraying of dangerous liquids against which higher chemical resistance is not required,
and against toxic solid particles carried by air (including asbestos fibers).
PROPERTIES:
three-panel hood, two-sided zipper with self-adhesive flap, two-piece cut in stride, elastic cuffs in cuffs,
legs, waist and hood; elastic thumb loop, antielectrostatic properties
FABRIC:
fabric laminated with microporous film (MPFL) 63g / m2, outer layer: polyethylene film, inner
layer: polypropylene fibers
COLOUR:
white
LIMITATIONS:
Exposure to certain chemicals or high concentrations may require higher protective properties through
the material or construction properties of the suit. Such areas can be protected with suits of types 1, 2, 3
and 4. The user will be the only one to assess compliance with the required type of protection and proper
connection of the suit with additional protective equipment.
METHOD OF PUTTING ON AND USING THE SUIT:
Before use, check that the selected product is suitable for the existing hazard and in the correct size
Check visually that the suit is intact (no piercing, no torn seams, etc.)
Remove the suit from the packaging, open the central zipper and put on the suit. Fasten the zipper
completely. In the case of solid particles, it is also recommended to seal the zipper
If protective gloves and/or shoe covers are used, seal the connection of the sleeves and gloves with the
shoe covers with self-adhesive tape.
WARNINGS:
The suit is intended for single use and should be discarded after use
Accepted configuration cannot be modified or changed
If tears, punctures etc. occur, immediately leave the workplace and put on a new suit
Do not remove the suit if the user is still in the danger area
Protective suits with electrostatic properties must not be opened or removed when in a
potentially explosive or flammable atmosphere or carrying explosive, flammable substances.
The person wearing clothing that protects against electrostatic charge should be properly
grounded. The resistance between man and earth should be reduced to less than 10
8
Ω, e.g. by
wearing appropriate footwear
Clothing that protects against electrostatic charge should cover all non-compliant materials during
normal use (including bending and movements)
Measurement of internal leakage is performed using dry aerosol particles (made from a sodium
chloride solution) with a mass median aerodynamic diameter = 0.6 μm
In cases where it is necessary to use additional PPE (such as gloves, footwear, respiratory
protection), they must be compatible with the suit and selected to provide full body protection
and must have at least equivalent chemical protection values.
To provide complete protection, all openings should be closed/sealed.
Extended wearing of chemical suits can cause heat stress.
Overheating and discomfort can be reduced or eliminated by using appropriate undergarments or
appropriate ventilation equipment.
The product is flammable - keep away from fire
TRANSPORT, STORAGE AND DISPOSAL:
The product must be transported and stored in the original packaging in dry rooms away from
sources of light and heat. If the suits are not contaminated, they can be disposed of with solid
municipal waste. If they have been contaminated, they must be disposed of in accordance with
applicable laws and regulations.
LIFETIME:
I
t is suggested to use the product within a period of five years from the date of production written
on label Month and year of production: MM/YYYY
INSTRUCTIONS FOR USE
PROTECTIVE CLOTHING , CATEGORY III, TYP 5,6
MODEL
:
OxyChem C 210
TECHNICAL PROPERTIES - RESULTS:
CONFORMITY WITH STANDARDS
Do not wash
Do not bleach
Do not dry
Do not iron
Do not clean
Flammable fabric
SIZES AND DIMENSIONS OF BODY (CM) – EN 13688:
MAINTENANCE AND CLEANING:
I-W1-001; wyd. 1; rev. 1.02.2019
Str. 1/1
8. Height and circumference of the chest
9. Size
10. The CE mark and the numer of the notified
body
11. QR code with a declaration of conformity
12. A disposable product
13. Symbols about maintenance
14. Month and year of production
PRODUCT LABEL (EXAMPLE):
1. Producer/Trademark
2. Pictograms specifyin the type of protection
3. Model designation
4. Product code
5. Lot number
6. Product barcode
7. Instructions in the packaging and information
The product was designed and marketed in accordance with the Regulation of the European
Parliament and of the Council (EU) 2016/425 dated 9 March 2016. on individual protection measures
and repealing Council Directive 89/686 / EEC
The body that certifies and supervising the product: Centro Tessile Cotoniero & Abbigliamento S.p.A.
(Centrocot), Piazza Sant'Anna 2, 21052 Busto Arsizio VA, notified body 0624
Producer: OXYLINE Sp. z o.o., ul. Piłsudskiego 23, 95-200 Pabianice, Poland
tel. +48 42 215 10 68, e-mail: [email protected], web: www.oxyline.eu
EU DECLARATION OF CONFORMITY:
The EU Declaration of Conformity is available at: https://www.oxyline.eu/deklaracje-kombinezony.html
Test on whole suits
Result
classes
Resistance to liquid penetration
Spray test type 6
(EN ISO 17491-4 met. A – EN 13034)
PASS
Resistance to aerosol penetration
Inward leakage type 5 (EN ISO 13982-2 – EN
ISO 13982)
L
jmn 82/90
≤ 30%
L
s 8/10
≤ 15%
PASS
Nominal protection factor (EN ISO 13982-2 –
EN 1073-2)
TIL
E
%
TIL
A
%
Fpn
Class 2
Practical performance tests (EN 1073-2)
Pass
Seams: strength (EN ISO 13935-2)
75-125 N
Class 3
Test on fabric
Result
Classificatio
n
Resistance to penetration to liquid
(EN ISO 6530 – EN 13034)
H2SO4 30%
<1%
NaOH 10%
< 1%
o-xilene
< 1%
Butan-1-ol
< 1%
Class 3
Class 3
Class 3
Class 3
Repellency to liquid
(EN ISO 6530 – EN 13034)
H2SO4 30%
> 95%
NaOH 10%
> 95%
o-xilene
90-95%
Butan-1-ol
90-95%
Class 3
Class 3
Class 2
Class 3
Abrasion Resistance (EN 530 - method 2)
10-100 cycles
Class 2
Trapezoidal tear resistance (EN ISO 9073-4)
20-40 N
Class 2
Tensile strength (EN ISO 13934-1)
30-60 N
Class 1
Puncture resistance (EN 863 - EN 1073-2)
10-50 N
Class 2
Flex cracking resistance (EN 7854)
> 100 000 c.
Class 6
Blocking resistance (EN 25978 - EN 1073-2)
Pass
Ignition and flammability (EN 13274-4 - EN 1073-
2 )
Pass
Electric surface resistance
≤ 2.5 x 10
9
Pass
Bursting strength (13938-1)
160-320 kPa
Pass
Resistance to penetration by blood-borne
phatogens - phi-x174 bacteriophage test - ISO
16603/16604
20 kPa
Class 6
Resistance to penetration by infective agents due
to
mechanical
contact
with
substances
containing contaminated liquids - ISO 22610 (test
microorganism: staphylococcus aureus)
t > 75
Class 6
Resistance to penetration by contaminated liquid
aerosols - ISO DIS 22611 (test microorganism:
staphylococcus aureus)
log > 5
Class 3
Resistance to penetration by contaminated solid
particles - EN ISO 22612
(test microorganism: spores of Bacillus subtilis)
1 < log ufc ≤ 2
Class 3
pH (EN ISO 13688 – ISO 3071)
3.5 > pH > 9.5
Pass
B
12
10
1
2
3
4
5
8
9
6
7
11
13
14
Batch number:
MM/YYYY
BARCODE
