manualshive.com logo in svg

OXTS RT Series, User Manual, Page: 49 / 133

Share
Download
OXTS RT Series User Manual Download Page 49

RT User Manual 

 

Revision: 190902 

49

 

 

 

 
‘Read settings from a raw data (RD) file:’ 

The RT writes the configuration it is using to 

the internally stored RD file. This option extracts the configuration used and loads it into 
the configuration wizard. Specify an RD file by clicking the ‘Browse’

… 

button. 

 

Read initial settings from device: 

If the RT is connected to the computer via Ethernet or 

WiFi it is possible to read the initial settings directly from the RT. The settings loaded are 
the settings that were last  committed to  the RT using NAVconfig or the factory default 
settings applied at manufacture stage. Select this option and enter the correct IP address of 
your RT or select it from the dropdown list. 

 

You must also specify the type of vehicle that the device is being installed in. This will 
tailor the settings available to edit in NAVconfig. 

 

Hardware Setup section in NAVconfig 

This section contains settings related to the position and orientation of the RT in the vehicle 
and  the  GNSS  antennas  as  well  as  the  profile  of  the  vehicle  in  which  the  RT  is  being 
installed (position of axles). It is broken up into tabs and it is recommended that you work 
through each tab in order. 

 

IMU orientation tab 

The IMU orientation tab is used to define the vehicle co-ordinate frame relative to the 
RT’s co-ordinate frame. It is important to get the orientation correct as although settings 
entered on this page do not affect the accuracy of the RT, if the outputs are not properly 
rotated to the vehicle frame then the measurements will appear incorrect. 

 

When using an RT-Strut, the orientation will need to be changed. Figure 19 shows an RT 
mounted on an RT-Strut in a vehicle. In this configuration, the 

y

-axis points left and the 

z

-axis points forwards. Other configurations are possible with the RT-Strut. 

 

 
 
 
 
 
 
 
 

Summary of Contents for RT Series






































































































































Reviews:

No comments