Owon SDS5032E User Manual Download Page 51

Page: 51 / 90

5. Advanced User Guidebook

Fig.5-35

Wave Saving

Tip:

Whatever the

Type

of save menu is set, you can save the waveform by just pressing

the

Copy

panel button in any user interface. If the

Storage

of the save menu is set as

External

", you should install the USB disk. Please refer to the contents below to

install the USB disk and name the file to be saved.

Save the current screen image:

The screen image can only be stored in USB disk, so you should connect a USB disk
with the instrument.

Install the USB disk

: Insert the USB disk into the "1.

USB Host port

" of "

Fig.

4-3

Right side panel". If an icon

appears on the top right of the screen, the

USB disk is installed successfully. The supported format of the USB disk: FAT32
file system, cluster size cannot exceed 4K. Once the USB disk cannot be
recognized, you could format it into the supported format and try again.

After the USB disk is installed, press the

Save

panel button, the save menu is

displayed at the bottom of the screen.

Press the

button, the

Type

menu will display at the left of screen, turn the

knob to choose

Image

for Type.

Press the

button, the input keyboard used to edit the file name will pop up.

The default name is current system date. Turn the

knob to choose the keys;

press the

knob to input the chosen key. The length of file name is up to 25

characters. Choose and press the

Enter

key of the keyboard to end the input and

store the file with the current name.

Summary of Contents for SDS5032E



























































































Search results

Summary of Contents for SDS5032E

Reviews:

Related manuals for SDS5032E

Brands by name

Popular brands

Owon SDS5032E, User Manual

Search results

Summary of Contents for SDS5032E

Reviews:

Related manuals for SDS5032E

Brands by name

Popular brands