Owon SDS5032E User Manual Download Page 26

Page: 26 / 90

5. Advanced User Guidebook

The description of the Channel Menu is shown as the following list:

Function Menu Setting

Description

Coupling

DC
AC
GROUND

Pass both AC and DC components of the input signal.
Block the DC component of the input signal.
Disconnect the input signal.

Inverted

OFF
ON

Display original waveform.
Display inverted waveform.

Probe

X1
X10
X100
X1000

Match this to the probe attenuation factor to have an
accurate reading of vertical scale.

1. To set channel coupling

Taking the Channel 1 for example, the measured signal is a square wave signal
containing the direct current bias. The operation steps are shown as below:

(1)

Press the

CH1 MENU

button and call out the CH1 SETUP menu.

(2)

Press the

button, the Coupling menu will display at the screen.

(3)

Press the

button to select the Coupling item as "

". Both DC and AC

components of the signal are passed.

(4)

Then, press

button to select the Coupling item as "

". The direct current

component of the signal is blocked. The waveforms are shown as Fig.5-2.

Fig. 5-2

AC Coupling Oscillogram

2. To adjust the probe attenuation.

For correct measurements, the attenuation coefficient settings in the operating
menu of the Channel should always match what is on the probe (see "

How to Set

the Probe Attenuation Coefficient

" on P14). If the attenuation coefficient of the

Summary of Contents for SDS5032E



























































































Search results

Summary of Contents for SDS5032E

Reviews:

Related manuals for SDS5032E

Brands by name

Popular brands

Owon SDS5032E, User Manual

Search results

Summary of Contents for SDS5032E

Reviews:

Related manuals for SDS5032E

Brands by name

Popular brands