manualshive.com logo in svg

Owlstone 90-0322 Series, Installation Instructions Manual

Share
Download
Owlstone 90-0322 Series Installation Instructions Manual Download Page 8

90-0322-AAA 

OHG Sub-Unit Installation Instructions

 

   20th Nov 2012 

© 2012 Owlstone Ltd  

Proprietary and Confidential  

Page 8 of 14 

Section 6 -  

Installing a Quick Connect in GEN-SYS 

 

Warning:  Swagelok fittings will leak if fitted incorrectly.  Owlstone will not take any 
responsibility for incorrect fitting of Swagelok fittings by the end user.   

The user must undertake a risk assessment before following this procedure.  The user is 
responsible for assessing chemical safety, COSHH and other risk implications. 

If the user requires the GEN-SYS system to be leak tight it must be tested after assembly.   
Please contact Owlstone for technical support regarding leak testing.   

1)  Prepare materials 

A Swagelok Quick Connect is supplied with your OHG (Owlstone p/n 50-0081). 

Two 

7/16” and a 5/8” spanner are required for this procedure. 

 

 

 

 

 

Figure 10: Quick connect

 

2) Remove Swagelok cap, fit Quick Connect 

Remove the 

Swagelok cap using the two 7/16” spanners before installing the quick connect. Swagelok 

fittings must be tightened by hand before turning an additional 1x half turn using a 7/16

” spanner.    

Do not over-tighten. 

          

 

 

Figure 11: Remove the cap 

 

 

Figure 12: Install the quick connect 

 

 

Summary of Contents for 90-0322 Series















Reviews:

No comments

Brands by name

Popular brands

Load more brands