manualshive.com logo in svg

Owlstone 90-0322 Series, Installation Instructions Manual

Share
Download
Owlstone 90-0322 Series Installation Instructions Manual Download Page 4

90-0322-AAA 

OHG Sub-Unit Installation Instructions

 

   20th Nov 2012 

© 2012 Owlstone Ltd  

Proprietary and Confidential  

Page 4 of 14 

Section 4 -  

Disconnect power + air from the GEN-SYS rack 

This section describes how to disconnect the GEN-SYS rack from air, exhaust and power services. 

 

Warning: Inlet gas line pressure must be vented before following this procedure. 

 

1)  Vent the gas supply line that provides pressure to the GEN-SYS system.   Do not proceed unless 

pressure has been vented from this line.   

2)  Using a 9/16

” spanner disconnect the inlet gas line from the rear of the GEN-SYS system. 

3)  If in use, using a 9/16

” spanner disconnect the exhaust line from the rear of the GEN-SYS system 

4)  The DC power connection is unscrewed by hand. 

 

 

Figure 2: Rear panel of GEN-SYS rack 

 

Disconnect Air Supply 

Disconnect Exhaust 

Disconnect DC Power 

 

Summary of Contents for 90-0322 Series















Reviews:

No comments

Brands by name

Popular brands

Load more brands