OWL WT-1 Operation Manual Download Page 31 | Manualshive

Page: 31 / 56

background image

OWL REPORTER

INSTALLING THE OWL USB DRIVER

To avoid USB driver conflicts, the OWL USB driver must be installed before connecting the WaveTester to the PC. Follow the
instructions below:

Insert the OWL CD into your CD-ROM drive.

When the CD Installation panel appears on your screen, click the “

Install USB Drivers

” button.

Click the “

Install

” button on the “

OWL USB to UART Bridge Driver Installe

r” dialog box.

Click the “

Continue Anyway

” button on the “

Software Installation

” dialog box.

Once the software installation is complete, click “

Yes

” to reboot the computer.

Connect the WaveTester optical power meter to a USB port on the PC using the supplied

USB download cable. The computer will automatically detect the WaveTester.

If Windows asks you to use Windows update to search for the driver, click the radio button

labeled “

No, not this time

”, then click “

Next

” to continue.

29

«
...
29
30
31
32
33
...
»

Summary of Contents for WT-1

























































Reviews:

No comments

Related manuals for WT-1

Brand: Omega Engineering Pages: 22

Brand: Abbott Pages: 296

Brand: Eaton Pages: 43

Brand: Oakton Pages: 69

Brand: jenway Pages: 50

Brand: jenway Pages: 62

Brand: OHAUS Pages: 19

Brand: OHAUS Pages: 54

Brand: Zenner Pages: 2

Brand: QuadTech Pages: 76

Brand: Xantrex Pages: 2

Brand: Xaoc Devices Pages: 8

Brand: ELGO Electronic Pages: 24

OPERA CONTROL CENTER SERVER - V 3.5

Brand: OPTICOM Pages: 21

Brand: Dakota Digital Pages: 38

Brand: Swema Pages: 4

Brand: Parkside Pages: 199

Brand: SEFRAM Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands