background image

PROBLEM

POSSIBLE CAUSE

SOLUTION

NOTES

Propane tank was not purged properly

Return the tank to an authorized propane station 
and re-purge the propane tank.

The Purge process requires that all air is removed 
from the propane tank prior to the first fill

The OPD float valve on the propane tank has 
been activated, closing the  valve and not 
allowing the tank to fill.

Attach the regulator to the propane tank, turn the 
control valve on for a few seconds to reset the 
OPD float valve.

The OPD float valve is a safety device which is 
activated when the propane tank has been filled 
too quickly.

Control valve not closed completely.

To shut off the valve, push the control valve in 
slightly to unlock and turn to the right (Clockwise) 
completely.

The far right position on the control valve is the 
off position

The regulator was not properly secured to the 
propane tank.

Disconnect the regulator and reconnect it properly 
to the propane tank.

The Regulator needs to be tightened securely & 
fully to the Propane Bottle to prevent propane 
leaks & to supply the correct amount of propane.

The tank was not purged properly, it contains a 
mixture of air and propane.  The results is 
intermittent flame, or flame extinguishes in a short 
period of time.

Burn off the remaining propane and re-purge the 
tank.

The purging process requires that ALL the air is 
removed from the propane tank during to the first 
fill to ensure maximum efficiency.  See your local 
authorized propane dealer.

In cooler temperatures, the liquid propane does 
not convert quickly enough to gas therefore 
causing the tank to freeze on the outside.

Turn the control valve to the low position where 
the flow is not a high.

Flame setting too low.

To Increase the flame, Turn the control valve 
clockwise to the 12 o'clock position to get the 
maximum amount of BTU's.

Flame setting too high.

To lower the flame, Turn the control valve counter 
clockwise from the 12 o'clock position a quarter 
turn to the set low position and a lower amount of 
BTU's.

Spiders may have created webs or insects may 
have created nests inside the venturi or orifice.

Make sure the fire pit is not is use & has not been 
used  recently and the unit is cold to the touch so 
as to not get burned.  Make sure the control valve 
is in the off position.  Close the propane tank valve 
or the fix piping supply line valve.  See page 12 of 
this manual on Converting Your Fire Pit to a 
Different Gas Type on how to access the venturi & 
the orifice.  Insert a small wire in the venturi & 
orifice holes to clear passage free of spider webs 
or other debris.  Make sure to put everything back 
correctly when finished for proper fire pit operation 
and safety.

This is a common problem when the fire pit has 
not been used for an extended period of time.

Low or Excessive Flame

Using Natural Gas

The water column may not have been adjusted 
correctly.

Contact your local licensed plumber or certified 
tech for assistance.

Fire Pit Wobbles

Cement slab or the use of natural stone may not 
be completely even.

Optional adjustable fire pit glides are available 
through your local dealer.

Optional glides are perfect for areas where the 
draining slope to level out a fire pit.

DO NOT 

 lift the glass wind guard until connector fittings hardware has been checked and is still secure to the glass guards.  Glass connectors may have become 

loose after use.  Make sure all glass connectors are secure after each use of the glass wind guard.

Clean

 glass wind guards only after completely cool to the touch, approximately 45 minutes after use, with water and white vinegar mix or commercially available 

streak-free glass cleaner and a soft cloth.  

DO NOT

 touch glass wind guard for 30-45 minutes following use.  

It will be hot.

Fire Pit Base - 

Rust seepage and or oxidation may occur in some crevices.  The area can be easily serviced by using a detail brush and or fine grit sandpaper.  Once 

the are is clear from rust seepage or oxidation, follow by wiping clean and applying touch-up to seal the crevice.  Contact your local dealer for the matching touch-up 
pen or aerosol.

Hammered Copper Tops -

  Using a stainless steel polish will help protect & keep the top looking nice.  Note: Always use coasters when setting drinks and or food on 

the top.  Spilling acidic drinks and food may discolor the hand applied patina.  Should the patina be removed with acidic elements, the area will darken over time.

Porcelain Table Tops

 - Clean with mild soap and water. Rinse with clean water to remove all soap residue.  Note: The grout is made from a durable outdoor epoxy 

which does not need to be sealed.  

Page 10

TROUBLE SHOOTING GUIDE

Propane Tank Does Not Fill

You Smell Propane or 

a Rotten Egg Smell

Immediately Stop!

See Warning & Instructions

on Page 1

Flame Problems:

No Flame

Intermittent Flame

Low Flame

ADDITIONAL CARE AND INSTRUCTIONS

DO NOT

 remove the glass wind guards until it has completely cooled, approximately 1/2 hour.  Check to be sure that all glass guard connector fittings have not come 

loose after the cooling process.

Summary of Contents for CASUAL FIRESIDE 5110-42RDO





























Reviews: