background image

Form No. OVmm-0912

13

MAINTENANCE

5. Wipe all surfaces clean using a damp, non-abrasive cloth.
6. Wipe dry all surfaces using a non-abrasive, dry cloth.
7. Perform the “Daily Cleaning” procedure in this section.

Cleaning the Slider assembly

Monthly Cleaning

1. Turn off the Standby switch and allow unit to cool. Cooling

fans will operate until the oven chamber temperature drops

below 140°F (60°C).

2. move the main Disconnect switch to the OFF (O) position

after the cooling fans shut off.

3. Remove and clean the two air filters on the back of the

oven. To clean each filter:

a. Slide the filter straight out the side of the filter bracket.
b. Spray  the  filter  with  water  and/or  soak  in  soap  and

water.

c. Rinse clean and allow the filter to air dry.

d. When the filter is dry, reinstall the filter into the filter

bracket.

Spray and clean right side

of center divider.

Spray and clean left side

of center divider.

Spray and clean

each end cap.

IMPORTANT NOTE

:

Use of cleaning chemicals not approved by Ovention when

cleaning the oven chamber will void the warranty.

Cleaning the air Filters

4. Remove and clean the upper and lower jet plates inside the

oven chamber. To clean the jet plates:

a. Unlatch and open the oven door so that the inside of the

oven chamber is exposed.

b. Remove the upper and lower jet plates. Remove the

plates by pulling the handles straight out of the oven.

c. Spray Chemco Dirt Buster III Oven Cleaner onto both

sides of each jet plate. allow the cleaner to sit for 3

5

minutes.

d. Using  a  non–abrasive  nylon  scouring  pad,  apply

pressure to wipe away grease residue.

e. Wipe the jet plates clean using a damp, non-abrasive

cloth and allow to air dry. Do not reinstall at this time.

Cleaning the Jet Plates

5. Clean the visible areas of the oven chamber using the

same procedure as the jet plates (steps “c” through “e”

above). 

6. Reinstall  the  upper  and  lower  jet  plates  into  the  oven

chamber.

7. Close the oven door and secure both door latches.
8. Perform the “Weekly Cleaning” procedure in this section.

Upper

Jet Plate

Oven

Door

Lower

Jet Plate

Door

Latch

Handle

Cord removed for clarity.

Air Filter

Temperature

High-Limit

Reset Button

Air Filter

Filter Bracket

Summary of Contents for Matchbox M1718

















Reviews: