background image

Form No. OVCM-0720

8

OPERATION

General

Use the following information and procedures to operate an 

Ovention

®

 Conveyor Oven.

WARNING

Read all safety messages in the IMPORTANT SAFETY 

INFORMATION section before operating this equipment.
In the event of emergency, turn OFF Main Disconnect 

switch.

CAUTION

BURN HAZARD: Some exterior surfaces on unit will get 

hot. Avoid unnecessary contact with unit.
Use caution and be aware of pinch points when slider 

assembly is moving.

Conveyor Setting Information

Conveyor Ovens are designed to provide unequaled flexibility 

and efficiency. Each oven has the capability of storing 36 

different conveyor settings. All conveyor settings appear on the 

Select Desired Item screen, which has eight additional sub-

screens.
At initial startup, the Select Desired Item screen will show 

either sample conveyor settings or customer-specific, 

preloaded conveyor settings. If the Select Desired Item screen 

shows sample conveyor settings, these settings can be used 

to help develop specific conveyor settings appropriate for the 

installation. Refer to the “Programming Conveyor Settings” 

procedure in this section for instructions on creating conveyor 

settings.

Startup

  1. Make sure the Main Disconnect switch is in the ON (I) 

position.

NOTE: The Conveyor Oven can be set up to cook from left-to-

right or right-to-left. This manual is written to reflect an 

oven set to cook from left-to-right. The conveyor belts 

on split belt models can travel in the same direction 

only.

  2.  Move the Standby switch up to the “On” position.
 

•  The touchscreen will energize and show the name of the 

oven and current software version for a few seconds.

Startup Screen

 

•  After the Startup Screen, the Select Desired Item screen 

appears. The first four pre-set conveyor settings are 

available on this screen.

Touch to scroll to next screen and

view additional conveyor settings.

Select Desired Item Screen—Single Belt Model

  3.  Touch the desired conveyor setting.
 

•  The oven heaters, air blowers, and cooling fans will start 

up. Allow 10–15 minutes for the oven to reach setpoint 

temperature.

  • The touchscreen shows the selected setpoint 

temperature and the current cavity temperature.

Touch to return to Select Desired Item

screen and select a different conveyor

setting.

Preheat Screen

When the oven reaches setpoint temperature, the oven begins 

a temperature stabilizing period (a countdown screen appears).

OVEN TEMPERATURE STABILIZING

OVEN TEMPERATURE STABILIZING

TIME REMAINING

TIME REMAINING

5:00

5:00

Oven Stabilizing Screen

After the oven temperature stabilizes, the conveyor belt begins 

moving and the Select Desired Item screen appears on the 

touchscreen. The oven is now ready for cooking.

NOTE: The conveyor settings shown are for example only. 

Depending on the configuration of the oven, the Select 

Desired Item screen will show either sample settings or 

customer-specific, preloaded settings.

Summary of Contents for Conveyor C2000 Series

















Reviews: