Outdoor Lifestyles TWILIGHT-II-MOD Installation Manual Download

Page: 25 / 28

Outdoor Lifestyles by Hearth & Home Technologies • Installation Manual TWILIGHT-II-MOD • 2290-970 Rev. H • 5/14

Appliance Setup

A. Fixed Glass Assembly

WARNING! Risk of Asphyxiation!

Handle

xed glass

assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.

•

DO NOT

strike, slam or scratch glass.

•

DO NOT

operate

replace with glass removed, cracked,

broken or scratched.

•

Replace as a complete assembly.

9.2 Glass Assembly - Interior Side

GLASS RETAINER BRACKET

WING NUT ON THREADED STUD

Removing Fixed Glass Assembly- Interior

• Loosen two wing nuts on bottom glass retainer bracket.
• Loosen and remove two wing nuts on top glass retainer

bracket. Remove glass retainer bracket. See Figure 9.1

• Lift glass assembly off of glass retainer bracket.

Replacing Fixed Glass Assembly - Interior

• Position glass assembly on bottom glass retainer bracket.

Tighten wing nuts on bottom glass retainer bracket.

• Position top of glass assembly, position top glass retainer

bracket and secure with two wing nuts.

9.1 Glass Assembly - Interior Side

WING NUT LOCATIONS

Summary of Contents for TWILIGHT-II-MOD





























Search results

Summary of Contents for TWILIGHT-II-MOD

Reviews:

Related manuals for TWILIGHT-II-MOD

Brands by name

Popular brands

Outdoor Lifestyles TWILIGHT-II-MOD, Installation Manual

Search results

Summary of Contents for TWILIGHT-II-MOD

Reviews:

Related manuals for TWILIGHT-II-MOD

Brands by name

Popular brands